Question

Measurement of the density of the material a coin is made of. In a test tube...

Measurement of the density of the material a coin is made of. In a test tube you have 15 mL of water initially. If you add 10 coins in test tube with water, the volume increases to final value of 19.25 mL; determine the density of the material that the coin is made of, if the mass of the 10 coins is 30.4 g.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A stoppered test tube that has a volume of 9.6 mL has 1.00 mL of water...
A stoppered test tube that has a volume of 9.6 mL has 1.00 mL of water at its bottom. The water has a temperature of 100ºC and is initially at a pressure of 1.00 atm. The test tube is held over a flame until the water has completely boiled away. Estimate the final pressure inside the test tube.
A solid sphere made of a composite material is floating in water with 41.0 % of...
A solid sphere made of a composite material is floating in water with 41.0 % of its volume above water. Note that the water density is 1.00 g/cm3, and the density of rubbing alcohol is 0.786 g/cm3. (a) The density of the composite material is g/cm3. (b) If we put this sphere in rubbing alcohol, it will have % of its volume above the alcohol surface.
A solid sphere made of a composite material is floating in water with 53.0 % of...
A solid sphere made of a composite material is floating in water with 53.0 % of its volume above water. Note that the water density is 1.00 g/cm3, and the density of rubbing alcohol is 0.786 g/cm3. (a) The density of the composite material is  g/cm3. (b) If we put this sphere in rubbing alcohol, it will have  % of its volume above the alcohol surface.
A.      Calculation of Density Density is a derived unit which is the ratio of the mass of...
A.      Calculation of Density Density is a derived unit which is the ratio of the mass of a substance to the volume occupied by that mass. Typical units are: kg/m3, g/mL or g/cm3. 1.      Weigh the wooden block you measured in Part A using the balance. 2.      Determine the density of wood. Complete Table 2. Include the correct number of significant figures and the uncertainty. Write your final answer in scientific notation. Compare your result to the accepted value. Calculate the percentage error....
If you were preparing a series of two 10% dilutions of pretend 1M HCl. You would...
If you were preparing a series of two 10% dilutions of pretend 1M HCl. You would have 3 test tubes labeled, 1, 2 and 3. Test tube 1 would be filled with 10 mL of the 1 M HCL. Always Add Acid to Water. This rule must be followed in order to prevent splattering of the acid. Use the formula to determine how much water should be added to test tube #2 to prepare a 10% dilution. The final desired...
You start your experiment with an empty test tube having a mass of 10.3362 g. You...
You start your experiment with an empty test tube having a mass of 10.3362 g. You are working with a hydrated compound of calcium sulfate. After adding the hydrate to the empty test tube, the mass of the test tube and hydrate is 14.5549 g. After heating the hydrate, you weigh the test tube again and the mass is 13.6737 g. Determine the number of moles of water in the original hydrated calcium sulfate compound. Hint: The hydrate will be...
The density of a 40 wt% solution of ethanol in water is 0.937 g/mL. The density...
The density of a 40 wt% solution of ethanol in water is 0.937 g/mL. The density of n-butanol is 0.810 g/mL. What is the concentration of n-butanol in ppm if you dissolve 15 μL of this alcohol in a 40 wt% solution of Ethanol in water. The final volume of the solution is 25 mL. Assume that the density of the ethanol solution does not change upon dissolution of the butanol. Use the correct number of significant figures!
1) You pipet a known amount of this standardized HCl into a 15 cm sample tube...
1) You pipet a known amount of this standardized HCl into a 15 cm sample tube and float a "boat" containing your unknown. You hook up the sample tube and contents to the gas buret. You shake the tube to sink the boat and to start the reaction. When the metal unknown is completely dissolved, you read the gas buret and measure the height of the buret's meniscus above the water level. Experimental Data: Volume of standardized HCl used 2.99...
I am doing a latenitelab on Molecular Mass by Freezing Poing Depression. I am stuck on...
I am doing a latenitelab on Molecular Mass by Freezing Poing Depression. I am stuck on three questions. 1.Suppose you added 4.000 g of FP sample #1 instead of 2.000 g, what would happen to the freezing point temperature of the water? 2. Suppose you dissolve 154.286 g of sodium chloride in 2.00 L of water. What is the molality of the solution given that the molar mass of sodium chloride is 58.44 g/mol and the density of water is...
14. Determine the molarity of a solution made by dissolving 1.21 moles of CaCl2 in enough...
14. Determine the molarity of a solution made by dissolving 1.21 moles of CaCl2 in enough water to make 250.0 mL of solution. (___M CaCl2 15. Determine the molarity of a solution made by dissolving 34.3 g of Sr(ClO3)2 in enough water to make 250.0 mL of solution. (___ M Sr(ClO3)2 16. Determine the volume (in mL) of a 1.62 M solution of ZnBr2 that contains 0.299 moles of ZnBr2. (____ mL) 17. Determine the mass of solute (in g)...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT