Question

What current would be required to lift a 1.0 g mass using the force balance? (Assume...

What current would be required to lift a 1.0 g mass using the force balance? (Assume the circuit doesnt overheat) Is it practical to use a device like the force balance to levitate a person?

Science   Physics   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
a) How many helium-filled balloons would it take to lift a person? Assume the person has...
a) How many helium-filled balloons would it take to lift a person? Assume the person has a mass of 67 kgkg and that each helium-filled balloon is spherical with a diameter of 33 cmcm. Express your answer using two significant figures. b) After landing on an unfamiliar planet, a space explorer constructs a simple pendulum of length 55.0 cmcm . The explorer finds that the pendulum completes 102 full swing cycles in a time of 128 ss . What is...
A car lift in a garage uses incompressible oil. A small input piston of radius 4.00...
A car lift in a garage uses incompressible oil. A small input piston of radius 4.00 cm is connected to a large piston of radius 16.00 cm via a sealed chamber. The large piston is connected to a platform on which rests a car. The combined mass of the platform and car is 1500 kg. (a) What is the minimum force required at the input piston to begin to raise the car? (b)What pressure is exerted at the small piston...
What mass of sodium borohydride (assuming no side reactions) would be required for the complete reduction...
What mass of sodium borohydride (assuming no side reactions) would be required for the complete reduction of 5.00g of cyclohexanone? The density of cyclohexanone is 0.95g/mL Mass of cyclohexanone is 100.2 g/mol Mass of sodium borohydride is 37.83 g/mol. The above is from the reduction reaction using NaBH4 to reduce cyclohexanone to cyclohexanol.
What mass of oxygen is required for complete combustion (to CO2 and H2O) of 227 g...
What mass of oxygen is required for complete combustion (to CO2 and H2O) of 227 g of butane. Using balanced equation 2C4H10 + 13O2---> 8 CO2 + 10 H2O.
What would be the length of the takeoff run (ft)? GIVEN INFORMATION: Use "g" = 32.2...
What would be the length of the takeoff run (ft)? GIVEN INFORMATION: Use "g" = 32.2 ft / s2 1 knot = 1.69 ft / s Gross Weight = 20,000 pounds Average Drag = 1,500 pounds Average Friction Force = 500 pounds Average Thrust = 10,000 pounds Lift Off Speed = 130 KTAS
A uniform rod of mass mr = 173 g and length L = 1... A uniform...
A uniform rod of mass mr = 173 g and length L = 1... A uniform rod of mass mr = 173 g and length L = 100.0 cm is attached to the wall with a pin as shown. Cords are attached to the rod at the r1 = 10.0 cm and r2 = 90.0 cm mark, passed over pulleys, and masses of m1 = 246 g and m2 = 127 g are attached. Your TA asks you to determine...
What mass of water in kg would remain in the container after 200. g of NaCl...
What mass of water in kg would remain in the container after 200. g of NaCl was added to the 1.00 L of water in a 1.00 L container? (Assume the density of water is 1.00 g/mL)
In the following reaction, what mass of mercury(II) oxide, HgO, would be required to produce 199...
In the following reaction, what mass of mercury(II) oxide, HgO, would be required to produce 199 L of oxygen, O2, measured at STP? 2HgO(s) --> 2Hg(s)+O2(g)
Consider the following chemical reaction: 2H2O(l)→2H2(g)+O2(g) What mass of H2O is required to form 1.5 L...
Consider the following chemical reaction: 2H2O(l)→2H2(g)+O2(g) What mass of H2O is required to form 1.5 L of O2 at a temperature of 325 K and a pressure of 0.946 atm ? Express your answer using two significant figures.
A Cr3+(aq) solution is electrolyzed, using a current of 7.80 A . 1. What mass of...
A Cr3+(aq) solution is electrolyzed, using a current of 7.80 A . 1. What mass of Cr(s) is plated out after 1.50 days? 2.What amperage is required to plate out 0.200 mol Cr from a Cr3+ solution in a period of 7.00 h ?
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT