Question

You need to build a circuit with a resistance of 2000 ohms. All you have at...

You need to build a circuit with a resistance of 2000 ohms. All you have at hand are several 4000 ohm resistors. You should:

1.

Connect two 4000 ohm resistors in parallel.

2.

Connect four 4000 ohm resistors in parallel.

3.

Use one 4000 ohm resistor and change the voltage used.

4.

The circuit can't be built with what you have, and you'll have to order some new electrical parts.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Supppose you have the following items to construct the circuit: two 9 V battery, two 100...
Supppose you have the following items to construct the circuit: two 9 V battery, two 100 ohm resistor, one 200 ohm resistor, one 300 ohm resistor and enough wires and clips. a)If you were to use all these items to build one circuit, how would you connect the resistors (parallel or in series) to find the smallest and largest current, that could be produced in a full circuit.(Draw both circuits you used to find them) b) Draw a new circuit,...
1.In your Ohm's law lab if you let the current (I) in your circuit remain constant,...
1.In your Ohm's law lab if you let the current (I) in your circuit remain constant, what will happen to the voltage (V) if the resistance (R) is tripled? 2.If you connect a 10-Volt supply voltage across a parallel combination of two 10 Ohm resistors, what should be the ammeter reading connected in series with the voltage source? 3.When you check a 7-Amps reading on your multimeter connected in series with a 3 Ohm resistor, what will the voltmeter reading...
A RLC circuit resonates at 5000 Hz it has an inductor with a DC resistance of...
A RLC circuit resonates at 5000 Hz it has an inductor with a DC resistance of 65 ohms, a 0.47 F capacitor and a 330 ohm resistor. What is the value of the inductor? What would be the impedance of the circuit at 2400Hz? What is the expected phase angle between the input voltage and the current at 2400 Hz? NEED ANSWERS FOR ALL 3 SINCE THEY ARE CONNECTED TO EACH OTHER. PLEASE AND THANK YOU!
2. The 60 W incandescent lamp and the 100 W incandescent lamp are each designed to...
2. The 60 W incandescent lamp and the 100 W incandescent lamp are each designed to be connected to a 220 V cable. Both lamps are connected in series and the string is connected to a 220 V mains supply. Explain which bulb will glow brighter. 1. Two conductors with resistances of 10 ohm and 20 ohm are connected in series. and the circuit is connected to a voltage of 60 v. A. Determine the current flow in each conductor....
(1)(A)What resistance do you need to connect in parallel to a 120 Ω resistor to get...
(1)(A)What resistance do you need to connect in parallel to a 120 Ω resistor to get a total of 51.0 Ω? (B)You have in your possession numerous resistors with a value of 3.50 mΩ each. hat is the smallest number you could hook together to get an effective resistance of 1.505 Ω? (Enter the smallest possible whole number of resistors.) (C)Your car's 27.7-W headlight and 2.75-kW starter are ordinarily connected in parallel in a 12.0-V system. What power would one...
QUESTION 1 How do you connect a voltmeter to a circuit? a) in series b) None...
QUESTION 1 How do you connect a voltmeter to a circuit? a) in series b) None of the answers is correct. c) either way is correct d) in parallel QUESTION 2 Can you connect a Digital multimeter (Ohmmeter) to a resistor in circuit to measure the resistance of resistor? a) No. b) Yes. c) Yes, if the Ohmmeter has a low internal resistance. d) Yes, if the Ohmmeter has a high internal resistance. QUESTION 3 Three resistors R1, R2 and...
QUESTIONS FOR SERIES AND PARALLEL CIRCUITS 1. i) How does the equivalent resistance of a series...
QUESTIONS FOR SERIES AND PARALLEL CIRCUITS 1. i) How does the equivalent resistance of a series circuit compare to each individual resistor? ii) Answer the same question for a parallel circuit? 2. Assume that you have three 2Ω resistors. Show using a schematic drawing, how youwould connect these together to achieve the following resistances: (a) 1Ω, (b) 3Ω, and (c)4 Ω. Note that you do not always have to use all three resistors to achieve your goal. PAGE 2 3....
Consider the following series circuit with a 105 volt battery and three resistors; R1=4 ohm, R2=5...
Consider the following series circuit with a 105 volt battery and three resistors; R1=4 ohm, R2=5 ohm, and R3=6 ohm a) Will the current in this circuit flow clockwise or counterclockwise? Explain your reasoning in three lines or less. b) What is the equivalent resistance of the three resistors above wired in series, in ohms? c) Draw the equivalent simple circuit. d) Find the current in the equivalent simple circuit, in amps. e) What is the current in the original...
Part 1: I need to design a circuit using only resistors and capacitors that will filter...
Part 1: I need to design a circuit using only resistors and capacitors that will filter out a signal above a specific frequency. In order to be deemed a success, the peak voltage across your capacitor must be equal to 20% of the peak voltage provided by the function generator at the frequency f_theory. Full credit on this lab requires that your percent error in Part 2 is less than 5%. f theory = 1699Hz Available values of resistance are...
1. A resistor with a resistance of 408 Ohms is connected to a 13 V battery...
1. A resistor with a resistance of 408 Ohms is connected to a 13 V battery . The current flowing through the resistor is a) 29.4 mA b) 4.896 A c) 12 mA d) 34 A 2) As you add more resistors in parallel to a circuit , the total voltage . a) remains the same b) increases c) decreases 3. A runner is approaching an ice cream truck that is double parked . The ice cream truck is playing...