Question

A cylindrical pressure vessel has a thickness of 10mm. The diameter of the pressure vessel is...

A cylindrical pressure vessel has a thickness of 10mm. The diameter of the pressure vessel is 450mm and its length is 2m. determine maximum internal pressure that can be applied if the longitudnal stress is limited to 200 MPA and the circumferential stress is limited to 80 MPA. Also find the allowable strain produced as a result of applied pressure if the Poisson ratio 0.3?

Science   Advanced-Physics   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

do comment for any difficulty.

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
a cylindrical pressure vessel with an outside diameter of 1000 mm is constructed be spirally wrapping...
a cylindrical pressure vessel with an outside diameter of 1000 mm is constructed be spirally wrapping a 15 mm thick steel plate and butt-welding the mating edges of the plate, the butt-welded seams form an angle of 30 with a transverse plane through the cylinder as shows . if the allowable normal stress perpendicular to the weld and the allowable shear stress parallel to the weld are 40 MPa and 15 MPa a respectively, determine the permissible internal pressure in...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load of 325 kN. If the compressive stress is 150 MPa, lateral strain for external diameter is is 0.000325 and Poisson’s ratio is 0.3, find the minimum wall thickness required for the column. Also calculate the shear modulus for the material of the column. Take E = 210 GPa.   
A cylindrical steel pressure vessel 30 cm in diameter and 1.5 cm thick contains a small...
A cylindrical steel pressure vessel 30 cm in diameter and 1.5 cm thick contains a small surface crack, oriented normally in the direction of the hoop stress. (a) Confirm that there is a leak condition before rupture, since the container experiences a cyclic gas pressure between 40 and 50 MPa and the fracture resistance of the material is 180 MPa√m. (b) At the point where the crack broke the wall thickness, calculate the rate of advance of the fatigue crack....
A simply supported polymer thin-walled vessel is subjected to the internal pressure P, as shown in...
A simply supported polymer thin-walled vessel is subjected to the internal pressure P, as shown in Figure 3. The tank is 6 m long, 2 m in outer diameter. The wall thickness of the tank is 20 mm. The tank and its contents have a weight distribution of q = 400 kN/m. If the pressure P = 200 kPa and the allowable stress of the polymer is allow = 30 MPa, determine the factor of safety against yielding according to...
A cylindrical storage tank contains liquefied propane under a pressure of 1.5 MPa (gage pressure P=1.5...
A cylindrical storage tank contains liquefied propane under a pressure of 1.5 MPa (gage pressure P=1.5 MPa) and is subjected to an axial force F=60 kN. Knowing that the tank has an inner diameter of 320 mm and a wall thickness of 3 mm, find the principal stresses and determine the maximum shear stress.
b. A cylindrical pressure vessel that is used for chemical processing is routinely pressurized to 26...
b. A cylindrical pressure vessel that is used for chemical processing is routinely pressurized to 26 MN m-2 . The vessel has a mean diameter of 1.6 m and a wall thickness of 0.095 m, and is constructed from welded plates of material with a UTS of 565 MN m-2 and a yield strength of 460 MN m-2 i.Calculate the maximum stress at full pressure that could drive the growth of a crack. ii.State, with justification, whether or not the...
Hot forging is used to reduce a metallic cylindrical workpiece with a diameter of 12 cm...
Hot forging is used to reduce a metallic cylindrical workpiece with a diameter of 12 cm and height of 25 cm to a height of 12 cm. Barreling of the workpiece is eminent knowing that the coefficient of friction of the open die plate with the workpiece is 0.3. The process takes 8 seconds to complete at a constant forging speed. The strength coefficient of the workpiece C= 200 MPa and strain rate sensitivity exponent m = 0.32. Calculate the...
A lightweight design of turbofan disc for an aero-engine has failed during a run-up test. The...
A lightweight design of turbofan disc for an aero-engine has failed during a run-up test. The disc can be taken to be of uniform thickness 125mm and has a central hole of diameter 300mm and an outer rim diameter of 700mm. The outer rim was loaded with 40 blades, each of mass 5kg evenly pitched around the periphery at an effective radius of 400mm. The disc had previously survived a run-up test with no blades attached. The titanium alloy used...
Steam is supplied to the heating coils of a reactor vessel at 125 psig, saturated. The...
Steam is supplied to the heating coils of a reactor vessel at 125 psig, saturated. The coils are 0.5-in. schedule 80 pipe (internal diameter= 0.546 in.). The steam is supplied from a main header through similar pipe with an equivalent length of 53 ft. The heating coils consist of 20 ft. of the pipe wound in a coil within the reactor. If the heating coil pipe shears accidentally, the reactor vessel will be exposed to the full 125-psig pressure of...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT