Question

A U-tube open at both ends is partially filled with water (Figure a). Oil having a...

A U-tube open at both ends is partially filled with water (Figure a). Oil having a density of 780 kg/m3 is then poured into the right arm and forms a column L = 5.16 cm high (Figure b).

(a) Determine the difference h in the heights of the two liquid surfaces.
cm

(b) The right arm is then shielded from any air motion while air is blown across the top of the left arm until the surfaces of the two liquids are at the same height (Figure c). Determine the speed of the air being blown across the left arm. Take the density of air as 1.20 kg/m3.
m/s

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in...
Water moves through a constricted pipe in steady, ideal flow. At the lower point shown in the figure below, the pressure is 1.65 ✕ 105 Pa and the pipe radius is 2.80 cm. At the higher point located at y = 2.50 m, the pressure is 1.27 ✕ 105 Pa and the pipe radius is 1.30 cm. (a) Find the speed of flow in the lower section. m/s (b) Find the speed of flow in the upper section. m/s (c)...
In a tube U mercury is poured, as in the left part of the figure. The...
In a tube U mercury is poured, as in the left part of the figure. The left arm of the tube has a cross-sectional area A1 of 10.00 cm2 and the right arm has a cross-sectional area A2 of 5.00 cm2. Then 40.0 g of water are poured into the right arm, as in the right part of the figure. Assuming that the mercury density is 13.6 g / cm3, calculate the distance h that mercury rises in the left...
Mercury is poured into a U-tube as shown in Figure a. The left arm of the...
Mercury is poured into a U-tube as shown in Figure a. The left arm of the tube has cross-sectional area A1 of 11.0 cm2, and the right arm has a cross-sectional area A2 of 4.90 cm2. One hundred grams of water are then poured into the right arm as shown in Figure b. Figure (a) shows a U-shaped tube filled with mercury. Both arms of the U-shaped tube are vertical. The left arm with cross-sectional area A1 is wider than...
A block of wood floats partially submerged in water. Oil is poured on top of the...
A block of wood floats partially submerged in water. Oil is poured on top of the water until the block of wood is totally submerged, partially in water and partially in oil as shown in the figure. A clear cup is partially filled with water, and has oil floating on top of the water, almost filling the vessel. Completely submerged in the fluids is a block. The block floats so that part of it is in the water and part...
A 1225-kg car is raised using a hydraulic lift, which consists of a U-tube with arms...
A 1225-kg car is raised using a hydraulic lift, which consists of a U-tube with arms of unequal areas, filled with oil with a density of 800. kg/m3 and capped at both ends with tight-fitting pistons. The wider arm of the U-tube has a radius of 18.0 cm and the narrower arm has a radius of 5.00 cm. The car rests on the piston on the wider arm of the U-tube. The wider piston is raised to a position that...
5. Consider sucrose diffusing along a 10 cm length of tube filled with water. The cross-sectional...
5. Consider sucrose diffusing along a 10 cm length of tube filled with water. The cross-sectional area of the tube is 6 cm2. The diffusion coefficient is 5.0 x 10–10 m2/s, and a total amount of sucrose of 8.1 x 10–14 kg is transported in steady state along the tube in 15 s. What is the difference in the density levels of sucrose at the two ends of the tube? (Answer in grams per cubic meter, g/m3.) Select one: a....
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT