Question

Heat Exchanger Design Question: In a Cross-Flow heat exchanger, is "R" dependent on the number of...

Heat Exchanger Design Question:
In a Cross-Flow heat exchanger, is "R" dependent on the number of tubes in the exchanger?
If so, what formula could be used to determine R?

R is the total thermal resistance
if it is the total, would the number of tubes need to be taken into account?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A thin-walled cross-flow heat exchanger is used to heat a petrochemical whose specific heat is 1800...
A thin-walled cross-flow heat exchanger is used to heat a petrochemical whose specific heat is 1800 J (kg K)-1 with hot water (Cp = 4180 J (kg K)-1). The petrochemical enters the heat exchanger at 20oC at a rate of 3.7 kg s-1, whilst the water stream enters at 110oC at a rate of 2.5 kg s-1. The heat transfer surface area of the heat exchanger is 4.8 m2 and the overall heat transfer coefficient is 940.30 W m-2K-1. Determine...
A 1-shell-2-tube pass heat exchanger is made of a steel alloy (thermal conductivity 45.4 W/(m K)....
A 1-shell-2-tube pass heat exchanger is made of a steel alloy (thermal conductivity 45.4 W/(m K). It is used to cool distilled water from 34oC to 29oC using water which flows inside tubes with an outer diameter of 19 mm and an inner diameter of 16 mm. The number of tubes in the shell is 160 (80 per pass). The mass flow rate of distilled water in the shell is 76180 kg/h. The cold water enters the heat exchanger at...
Question 2. Answer all parts of this question a) A shell and tube heat exchanger is...
Question 2. Answer all parts of this question a) A shell and tube heat exchanger is to heat 10,000 kg h–1 of water from 16 to 84°C using hot oil entering at 160°C and leaving at 92°C. The oil will flow through the shell of the heat exchanger. The water will flow through 11 brass tubes of 22.9 mm inside diameter and 25.4 mm outside diameter, with thermal conductivity 137 W m–1 K–1, with each tube making two passes through...
Water is used to cool R-134a in the condenser of a heat exchanger. The refrigerant enters...
Water is used to cool R-134a in the condenser of a heat exchanger. The refrigerant enters the counter-flow heat exchanger at 800 kPa, 80 0C and a mass flow rate of 2 kg/s. The refrigerant exits as a saturated liquid. Cooling water enters the condenser at 500 kPa and 18 0C and leaves the condenser at 30 0C. Determine the necessary mass flow rate of water. Each fluid is assumed to flow at constant pressure.
Water at a flow rate of 60 kg/s enters the shell-side of a baffled shell-and-tube heat...
Water at a flow rate of 60 kg/s enters the shell-side of a baffled shell-and-tube heat exchanger at 35 °C and leaves at 25 °C. The heat will be transferred to 150 kg/s of raw water coming from a supply at 15 °C. You are requested to design the heat exchanger for this purpose. A single shell and single tube pass is preferable. The tube diameter is ¾ in. (19 mm outer diameter with 16 mm inner diameter) and tubes...
A 1 shell pass, 4 tube pass shell-and-tube heat exchanger is used to cool therminol 59...
A 1 shell pass, 4 tube pass shell-and-tube heat exchanger is used to cool therminol 59 in a refinery. The therminol 59 enters the tubes at a mass flow rate of 0.87 kg/s and changes in temperature from 93◦C to 49◦C. Water is the other fluid. It enters the shell at a mass flow rate of 1.20 kg/s, and changes in temeperture from 23◦C to 37.1◦C. Determine the following: (a) (10 pts) The heat transfer between the two fluids (b)...
If it wasn't possible to change flow direction in a heat exchanger, what would you need...
If it wasn't possible to change flow direction in a heat exchanger, what would you need to do instead to produce a parallel flow that produces a smaller heat transfer than that of the counter flow?
An automatic welder is used to join a large number of tubes in a heat exchanger...
An automatic welder is used to join a large number of tubes in a heat exchanger assembly. Each weld is inspected, and most of them are satisfactory. However, some need repair by a re-machining and re-welding process. In a sample of 65 qualification welds, eight were found to require the repair process. Perform the appropriate hypothesis test to determine whether there is evidence that the repair probability differs from 10%. A very approximate 100·(1 – a)% confidence interval for a...
Question 4 Saturated steam at 227°C is used in a heat exchanger to preheat a reactor...
Question 4 Saturated steam at 227°C is used in a heat exchanger to preheat a reactor feed stream. (a) If the condensate (saturated liquid) is removed from the heat exchanger at 152°C and the flow rate is 1000 kg/h, how much heat (kJ) is transferred from the steam to heat up the reactor feed stream in one hour? (b) How much additional steam would be required if the condensate is removed at 227°C, instead of 152°C, for the same exit...
A shell and-tube heat exchanger is required for the following service: Hot stream Cold Stream Aromatic...
A shell and-tube heat exchanger is required for the following service: Hot stream Cold Stream Aromatic Stream Cooling Water inlet Temperature (oC) 85 20 outlet Temperature (oC) 40 35 Mass Flowrate x heat Capacity (kW/oC) 85.2 Hot Stream cold stream (Cooling water) Heat Capacity (J/kg K) 2840 4193 Density (kg/m3) 750 999 Viscosity (cP) 0.34 1.016 Thermal conductivity (W/m.K) 0.19 0.594 Fouling Factor (m2.oC/W 0.00018 0.000176 ? The cooling water is allocated to the tube-side of the exchanger. ? It...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT