Question

A 100-m long horizontal pipe carries water at an average velocity of 2.5 m/s. The required...

A 100-m long horizontal pipe carries water at an average velocity of 2.5 m/s. The required pressure drop, deltaP, across the length of the pipe required to achieve this is 1.5 x 10^5Pa, and the surface roughness to diameter ratio of the inside of the pipe is k/D= 0.004. What is the diameter of the pipe?

The only current example on chegg of this problem is wrong.

Homework Answers

Answer #1

Hope this will be helpful

Page 1

Page 2

Give your feedback

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the...
The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the loss of head through an abrupt contraction to 50 mm diameter. If the pressure in the 150 mm pipe is 345 kPa, what is the pressure in the 50 mm pipe, neglecting pipe friction?
Water at 10 ◦C enters a circular pipe of internal diameter 2.5 cm with an average...
Water at 10 ◦C enters a circular pipe of internal diameter 2.5 cm with an average velocity of 1.2 m/s. Steam condenses on the outside of the pipe so as to keep the surface temperature of the pipe at 82 ◦C. If the length of the pipe is 5 m, determine the outlet temperature of water.
2 parts! thanks :) 1. A water pipe with an inner diameter of 2.5 cm carries...
2 parts! thanks :) 1. A water pipe with an inner diameter of 2.5 cm carries water into the basement of a house at a speed of 0.88 m/s and a pressure of 180 kPa. If the pipe tapers to an inner diameter of 1.2 cm and rises to the second floor 7.2 m above the input level, what is the speed of the water flow at the second floor? Your answer should be in m/s, but enter only the...
The water enters the two-story building through a horizontal pipe with an inner diameter 4 cm...
The water enters the two-story building through a horizontal pipe with an inner diameter 4 cm and the pressure of 10 atm. The velocity of the water flow in the pipe is 5 m/s. The horizontal pipe is connected to a vertical pipe which leads to bathrooms in each story. a) What is the velocity of the water flow in the vertical pipe if the diameter of the pipe is 2 cm. b) What is the pressure in the pipe...
Water is flowing at the rate of 1.676 m/s in a 3.068 inches’ diameter horizontal pipe...
Water is flowing at the rate of 1.676 m/s in a 3.068 inches’ diameter horizontal pipe at a pressure p1 of 68.9 kPa. It then passes to a pipe having an inside diameter of 2.067 inch. The density of the water is 998 kg/m3 . a) Calculate the new pressure p2 in the 2.067inch pipe. Assume no friction losses b) If the piping is vertical and the flow is upward, calculate the new pressure p2. The pressure tap for p2...
Liquid water flows in a long pipe of internal diameter of D = 0.01 m at...
Liquid water flows in a long pipe of internal diameter of D = 0.01 m at a mean velocity of V = 0.065 m/s. The pipe is maintained at a constant and uniform surface temperature. Assume the flow is both hydrodynamically and thermally fully developed. For simplicity, evaluate the properties of water at 300 K. Calculate the convective heat transfer coefficient of the flow inside the pipe in W/m2K?
In a horizontal pipe, water enters with a velocity of 2m / s when it is...
In a horizontal pipe, water enters with a velocity of 2m / s when it is subjected to a pressure at the inlet of 200 Pw (water pressure). Determine: a) The speed of the water (in m / s) at the outlet if an outlet pressure of 134 Pw is observed    b) If the area of ​​the tube at the inlet is 0.75m2, find the volumetric flow at the outlet. (in m3 / sec)
1.2 A horizontal Venturi meter is used to measure the flow of water in a 400mm...
1.2 A horizontal Venturi meter is used to measure the flow of water in a 400mm diameter pipe. The throat diameter of the Venturi meter is 100mm and the the discharge coefficient is 0.85. if the pressure difference between the two measurement points is 10cm of mercury, then calculate the average velocity in the pipe. take the relative density of mercury as 13.6. b) What diameter pipe would be required to double the capacity for the 400mm concrete conduit pipe...
A horizontal pipe with an outer surface temperature of 80 * C and an outside diameter...
A horizontal pipe with an outer surface temperature of 80 * C and an outside diameter of 100 mm is located in a room at atmospheric pressure at 20 ° C. Find the required pipe length for the loss of heat from the pipe to 1 kW. (Physical properties for air k = 0.0287 W / mK, Pr = 0.70, v = 19x10-6 m² / s)
1- Water flows in a 10 m long and 4 cm diameter pipe contains 4 elbows...
1- Water flows in a 10 m long and 4 cm diameter pipe contains 4 elbows ( KL= 0.2 ) at velocity 8 m/s. Calculate the total head losses when the friction factor f=0.03 35.56 m 22.07 m 27.07 m 15.46 m 2- water flows in a 10 m long and 5 cm diameter horizontal pipe at rate 15 l/s Calculate the pressure drop Take the density of water 1000 kg/m3 and the dynamic viscosity 0.001 kg/m.s 74.13 kPa 96.41...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT