Question

A shaft with a diameter of 75 mm is subjected to a torque of 461 N-m....

A shaft with a diameter of 75 mm is subjected to a torque of 461 N-m. What is the stress, MPa?

Homework Answers

Answer #1

STRESS IN A CYLINDRICAL SOLID SHAFT IS CALCULATED BY USING TORSION EQUATION:

T/J = τ/R ,

which means , TORQUE TRANSMITTED/POLAR MOMENT OFINERTIA = TORSION STRESS/ RADIUS OF SHAFT

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A solid steel shaft, 20 mm in diameter and 1 m long, is placed concentrically inside...
A solid steel shaft, 20 mm in diameter and 1 m long, is placed concentrically inside a hollow duralumin shaft with inside and outside diameters of 30 mm and 33 mm respectively and a length of 500 mm. The ends of the hollow shaft are rigidly fixed to the solid shaft. Determine (a) the torsional stiffness of the composite shaft (b) the maximum torque to which the composite shaft may be subjected if the allowable shear stresses for steel and...
‏A 50 mm diameter shaft is made from carbon steel having ultimate tensile strength of 630...
‏A 50 mm diameter shaft is made from carbon steel having ultimate tensile strength of 630 MPa. It is subjected to a torque which fluctuates between 2000 N-m to - 800 N-m. Using Soderberg me thod, calcukate the factor of safety. Assume suitable values for any other data needed.
Determine the critical diameter in mm for a shaft under bending. The shaft is to be...
Determine the critical diameter in mm for a shaft under bending. The shaft is to be made from a material with a Sut of 600MPa. The shaft is subjected to a maximum bending moment of 9Nm and a midrange torque of 5Nm. The shaft is to be machined, needs to have an efficiency of 95% and operate at room temperature. The required stress-concentration factor (Kf) is 1.7 (Kfs = 1.5). It can be assumed that Kb = 1 and the...
Find the outside and inside diameter of a mild steel hollow shaft if with allowable shear...
Find the outside and inside diameter of a mild steel hollow shaft if with allowable shear stress (42 Mpa) with a transmitting torque of (955*10^3 N-mm) take the ratio of inside diameter to outside diameter (0.5)
A solid alloy shaft of 50 mm diameter is coupled in series with a hollow steel...
A solid alloy shaft of 50 mm diameter is coupled in series with a hollow steel shaft of same external diameter. Determine the internal diameter of the hollow steel shaft if the angle of twist per unit length in hollow shaft is 75% of that of the solid alloy shaft. Also, determine the speed at which the compound shaft must be driven to transmit 200 kW, if the limiting shear stresses are 55 MPa and 75 MPa in alloy and...
A shaft of 2m length, 30 mm radius, with a wall thickness of 5 mm has...
A shaft of 2m length, 30 mm radius, with a wall thickness of 5 mm has a torque applied of 450 N. If the material has a G value of 275 GPa, what is the angular deflection in radians and degrees? Hint, you need to calculate the J value, T x l/J x G = deflection, and then convert to degrees. (up to 15 points) A torque of 1500 N on a shaft of 20 mm radius will have what...
A shaft is loaded in bending and torsion such that Ma = 70 N · m,...
A shaft is loaded in bending and torsion such that Ma = 70 N · m, Ta = 40 N · m, Mm = 50 N · m, and Tm = 30 N · m. For the shaft, Su = 700 MPa and Sy = 560 MPa, and a fully corrected endurance limit of Se = 210 MPa is assumed. Let Kf = 2.2 and Kfs = 1.8. With a design factor of 2.0 determine the minimum acceptable diameter of...
A center-cracked panel with an initial crack length of 0.010 mm is subjected to a tensile...
A center-cracked panel with an initial crack length of 0.010 mm is subjected to a tensile cyclic stress between 25 and 125 MPa for 350000 cycles. The panel is then subjected to a tensile cycle stress between 0 and 250 MPa. How many of the larger stress amplitude cycles can be sustained before failure? The material has a fracture toughness of 25 MPa?m and material constants n = 3.1 and C = 1.8 x 10-10 for these units.
the 150mm diameter shaft rotates at 1500 r.p.m. within a 200 mm long journal bearing with...
the 150mm diameter shaft rotates at 1500 r.p.m. within a 200 mm long journal bearing with 150.5 mm internal diameter. The uniform annular space between the shaft and the bearing is filled with oil of dynamic viscosity 0.8 poise. what is the shear stress on the shaft ?
The drive shaft AB of an automobile with 1.7 m long is made of a steel...
The drive shaft AB of an automobile with 1.7 m long is made of a steel having an allowable shear stress τall = 60 MPa and modulus of rigidity G = 80 GPa. Limit angle of twist of the shaft is 0.035 rad. If the outer diameter of the shaft is 65 mm and the engine delivers 180 kW to the shaft when it is turning at 1170 rev/min, determine the minimum required thickness of the shaft’s wall.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT