Question

What is the equation for the fanning friction factor (f) in a: Turbulent flow? Laminar flow?...

What is the equation for the fanning friction factor (f) in a:
Turbulent flow?
Laminar flow?
Transitional flow?
(In all cases rough and smooth pipe)
Engineering   Chemical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
In both laminar and turbulent flow, is the pressure drop within a pipe with rough surface...
In both laminar and turbulent flow, is the pressure drop within a pipe with rough surface negligible or large?
Explain how you may determine if flow in a pipe is laminar or turbulent? Why is...
Explain how you may determine if flow in a pipe is laminar or turbulent? Why is the distinction between laminar and turbulent important in fluid mechanics?
For a three-tank system that has a Fanning friction factor that depends on velocity, numerical simulations...
For a three-tank system that has a Fanning friction factor that depends on velocity, numerical simulations will be required. If the Blasius equation is used as a model for the Fanning friction factor, write out the system of differential equations and describe how they would be solved numerically. ****Three tanks are interconnected by pipes leading from the bottom of each tank to the other two tanks. Two of the tanks are identical and have the diameter of 11". The diameter...
Friction loss in turbulent flow Type I problem: Use Figure 6.10 to determine the head loss...
Friction loss in turbulent flow Type I problem: Use Figure 6.10 to determine the head loss per 100 ft for water flowing at 60 gallons per minute in a nominal 2-inch ID commercial steel pipe (you need to find actual ID from Appendix A.2 table). Use the density and viscosity given in our text for water at 68 ?F.
(Laminar flow) Asphalt at 120°F, considered to be a Newtonian fluid with a viscosity 88,000 times...
(Laminar flow) Asphalt at 120°F, considered to be a Newtonian fluid with a viscosity 88,000 times that of water and a specific gravity of 1.60, flows through a pipe of diameter 2.00 in. If the pressure gradient is 1.64 psi/ft, determine the flowrate assuming the pipe is (a) horizontal (ft3/s) (b) vertical with flow up (ft3/s)
An industrial pump is to be used to supply water from Lake Bonno to an agricultural...
An industrial pump is to be used to supply water from Lake Bonno to an agricultural field located 500 m away from the lake, and at an elevation of 20 m above the surface of the lake. If the horse-power of the pump is 45-hp, what is the discharge that can be delivered by using a pipe of diameter D = 0.4 m and a friction coefficient of f = 0.015? Neglect all minor losses. Is the flow laminar or...
Motor oil at T=-30 deg F has a kinematic viscosity of ν=0.11ft2/s and a specific gravity...
Motor oil at T=-30 deg F has a kinematic viscosity of ν=0.11ft2/s and a specific gravity of SG=0.88. (The rest of this is made up numbers and may not be indicative of actual car engine behavior) Assume that the oil flows at a velocity of V=2ft/s through a cast iron conduit within the engine block. Treat the conduit as a “best case roughness” (use smallest number for ε if needed) cast iron pipe with a diameter of 0.5in and a...
Which parameters are effective in the determination of friction factor, f and drag coefficient, CD depending...
Which parameters are effective in the determination of friction factor, f and drag coefficient, CD depending on flow regime?
A 250 mm diameter of cast iron pipe flows 39.3 L/s of SAE 10 oil along...
A 250 mm diameter of cast iron pipe flows 39.3 L/s of SAE 10 oil along 500 m length. Given: dynamic viscosity, μ and density, ρ of SAE 10 oil are 1.04 x 10-1 Ns/m2 and 917 kg/m3 respectively. By assuming the flow is laminar, determine energy head and pressure loss due to pipe friction using Hagen-Poiseuille equation and friction factor, f.
2. (25pts) Motor oil at T=-30 deg F has a kinematic viscosity of ν=0.11ft2/s and a...
2. (25pts) Motor oil at T=-30 deg F has a kinematic viscosity of ν=0.11ft2/s and a specific gravity of SG=0.88. (The rest of this is made up numbers and may not be indicative of actual car engine behavior) Assume that the oil flows at a velocity of V=2ft/s through a cast iron conduit within the engine block. Treat the conduit as a “best case roughness” (use smallest number for ε if needed) cast iron pipe with a diameter of 0.5in...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT