Question

Two steel plates ( 110 mm ) wide and ( 15 mm ) thick are to...

Two steel plates ( 110 mm ) wide and ( 15 mm ) thick are to be joined by double transverse fillet weld , the dynamic tensile stress is not exceed ( 46.66 MPa ). Find the length of the weld for:- 1- Static loading , and 2- Dynamic loading. *

Two steel plates ( 110 mm ) wide and ( 15 mm ) thick are to be joined by double transverse fillet weld , the dynamic tensile stress is not exceed ( 46.66 MPa ). Find the length of the weld for:- 1- Static loading , and 2- Dynamic loading. *

Homework Answers

Answer #1

Ans:

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
WITH COMPLETE SOLUTION A welded steel girder having the cross section of two fabricated 280 mm...
WITH COMPLETE SOLUTION A welded steel girder having the cross section of two fabricated 280 mm x 25 mm flange and a 600 mm x 15 mm web plate. The plates are joined by four fillet welds that run continuously for the length of the 6 m span girder. Each weld has an allowable load of 330 kN/m. 1.Determine the maximum allowable shear force V for the girder in kN. 2. Calculate the maximum bending stress of the girder if...
A leaf spring is to be made of seven steel plates 65 mm wide and 6.5...
A leaf spring is to be made of seven steel plates 65 mm wide and 6.5 mm thick. Calculate the length of the spring, so that it may carry a central load of 2.75 kN, the bending stress being limited to 160 MPa. Also calculate the deflection at the centre of the spring. Take E for the spring material as 200 GPa
mechanical component is 200 mm wide, and 10 mm thick, made of aluminum and yields a...
mechanical component is 200 mm wide, and 10 mm thick, made of aluminum and yields a stress of 240 Mpa. calculate the max safe load P if the normal stress cannot exceed yield stress. Factor of safety is 3.
a cylindrical pressure vessel with an outside diameter of 1000 mm is constructed be spirally wrapping...
a cylindrical pressure vessel with an outside diameter of 1000 mm is constructed be spirally wrapping a 15 mm thick steel plate and butt-welding the mating edges of the plate, the butt-welded seams form an angle of 30 with a transverse plane through the cylinder as shows . if the allowable normal stress perpendicular to the weld and the allowable shear stress parallel to the weld are 40 MPa and 15 MPa a respectively, determine the permissible internal pressure in...
Q2: Three steel plates each having thickness 1.2 cm and width 6 cm are joined by...
Q2: Three steel plates each having thickness 1.2 cm and width 6 cm are joined by using two rivets having diameter 15 mm each. When the plates are subjected to an external force of 65 MN, what will be the shear stress developed in the rivet? If the ultimate shear strength on the rivet is limited to 1500 tonnes/cm2, what will be the maximum load that can be carried by the plate? Instead of three plates, if two steel plates...
A triple riveted butt joint which is used to connect two 8 mm thick plates. The...
A triple riveted butt joint which is used to connect two 8 mm thick plates. The rivet diameter and the pitch are 10 mm and 50 mm respectively. Determine the efficiency of the riveting system. Assume the rivet material has the same properties of plate material used if need power 1kw velocity 500rpm ultimate stress 680Mpa yield stress 400Mpa shaft diameter50mm   tension=compression
1. Consider a 1.8-m high and 1.5 m-wide double-pane window consisting of two 4-mm thick layers...
1. Consider a 1.8-m high and 1.5 m-wide double-pane window consisting of two 4-mm thick layers of glass (k = 0.78 W/m°C) separated by a 10-mm wide stagnant air space (k = 0.026 W/m°C). The room is maintained at 20°C while the temperature of the outdoors is -10°C. Take the convective heat transfer coefficients on the inner and outer surfaces of the window to be 10 W/m2°C and 40 W/m2°C, respectively. Determine the steady rate of heat transfer through this...
A normal mild steel specimen having 50 mm 2 cross section area and 10 cm long...
A normal mild steel specimen having 50 mm 2 cross section area and 10 cm long gauge length was tested. 1. Draw the stress- strain diagram 2. calculate the final length of the bar compare when the specimen unloaded from 400 MPa? 3. calculate the elastic and plastic deformation when the specimen unloaded from 400 MPa Proportionality limit Ultimate Load Failure Load Stress (MPa) 320////// 500 /////////400 Strain 0.0018 //// 0.06///////// 0.12
Problem 1: A round bar with a diameter of 32 mm, and 4012 mm in length...
Problem 1: A round bar with a diameter of 32 mm, and 4012 mm in length was under tensile test to determine the mechanical properties of the material. The following table shows the load versus strain data collected from the testing machine and a strain gauge applied on the bar in the loading direction. The measured percentage elongations were 19.8 % and 14.6 % on gauge lengths of 100 mm and 200 mm respectively. Assume: the elongations include the necking;...
Your firm has designed a new 2m​ double-paned window which consists of two 5 mm thick...
Your firm has designed a new 2m​ double-paned window which consists of two 5 mm thick plates of glass (​k​ = 0.75 W/mK) separated by a 14 mm thick layer of xenon gas with an unknown thermal conductivity, which you intend to determine through an experiment. You use a heater that provides 100 W of heat to maintain one side of the window at 80 °C while the other 2​ side is exposed to the air in the room with...