Question

Course: Heat transfer 2-) In Forced and Natural Transport, write the Laminar and Turbulent flow separator...

Course: Heat transfer

2-) In Forced and Natural Transport, write the Laminar and Turbulent flow separator criterion and value for different geometries.

Homework Answers

Answer #1

Simply For Flowing Fluid , we can distinguish Laminar and Turbulent Flow by REYNOLDS NO .

Reynolds No - It is basically a ratio of inertia force to viscous force . Its a dimensionless no

A.) PIPE FLOW -

Laminar Flow - Reynolds no is less than 2000 . Turbulent Flow - Reynolds no is more than 4000 .

B.) OPEN CHANNEL FLOW -

Laminar Flow - Reynolds No is less than 500 Turbulent Flow - Reynolds no is more than 1000 .

If have any doubt , please can ask me again anytime .... Please appreciate the effort done , Thank you .

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Please answer the questions carefully. 1.Convection heat sytems can be Radiation heat forced air driven passive...
Please answer the questions carefully. 1.Convection heat sytems can be Radiation heat forced air driven passive operate in a vaccuum 2.UV Lithography the story of a wave and its adverse effects still experimental used to make AMD chips The etching used to write Intel on every chip 3.100 million times better than the Human eye Night Goggles Electron Microscope Hubbel Telescope Haggis Register 4.Which is the correct explanation of the difference between Laminar and Turbulent flow? Laminar flow has complex...
Problem 2. (20 pts) You would like to know the heat transfer coefficient from a cooling...
Problem 2. (20 pts) You would like to know the heat transfer coefficient from a cooling fin operating under forced convection, but with a length of 1 cm the real fin is just too small to make any measurements. You make a 10x scale model and test it at the real operating temperatures and 1/10th the ambient airflow velocity. If your scale model has an h of 5.14 W/m2/K, what is the value of h for the real fin? In...
1) An isentropic flow: a) has no heat transfer, b) does not allow temperature to change,...
1) An isentropic flow: a) has no heat transfer, b) does not allow temperature to change, c) can occur in a real physical problem, d) can only occur when the fluid is at rest. 2) Based on the first law of thermodynamics (assuming no chemical reactions, i.e. just a simple gas like air or helium): a) changing the flow velocity can heat the flow, b) moving a solid body through a fluid can heat the fluid, c) compressing a perfectly...
1. An oven chimney is made of brick with a heat transmission coefficient 1.1 W/mK 10...
1. An oven chimney is made of brick with a heat transmission coefficient 1.1 W/mK 10 cm thick. Since the shaft exterior radiation beam coefficient is 0.8 and the flue gas temperature is 350°C, the external ambient temperature is 25°C and the outer ambient heat transport coefficient is 20 W/m2K; a) Calculate the shaft exterior temperature. b) In order to reduce the risk of burn injury that may occur in the body, the shaft is asked to be below 55°Cve...
Please read the article and answear about questions. Determining the Value of the Business After you...
Please read the article and answear about questions. Determining the Value of the Business After you have completed a thorough and exacting investigation, you need to analyze all the infor- mation you have gathered. This is the time to consult with your business, financial, and legal advis- ers to arrive at an estimate of the value of the business. Outside advisers are impartial and are more likely to see the bad things about the business than are you. You should...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT