Question

The nominal size of a shaft is 65mm. Given that the maximum diameter is 65.12mm and...

The nominal size of a shaft is 65mm. Given that the maximum diameter is 65.12mm and the tolerance required is 25µm. Determine the minimum size of the diameter. If tolerance grade specified in the drawing is IT7, determine whether the drawing will pass the inspection.

Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

Hope you like the solution so I kindly request you to upvote.

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A hole and a shaft system has a nominal dimension of 30 mm with a fit...
A hole and a shaft system has a nominal dimension of 30 mm with a fit type H7h8 fit. Determine: Fundamental Deviation of the Shaft Fundamental Deviation of the Hole If the nominal diameter lies within the range of 18 and 30, find the maximum and minimum size of the hole. Maximum and minimum size of hole Maximum and minimum size of shaft Width of the tolerance zone for hole and shaft
Determine the critical diameter in mm for a shaft under bending. The shaft is to be...
Determine the critical diameter in mm for a shaft under bending. The shaft is to be made from a material with a Sut of 600MPa. The shaft is subjected to a maximum bending moment of 9Nm and a midrange torque of 5Nm. The shaft is to be machined, needs to have an efficiency of 95% and operate at room temperature. The required stress-concentration factor (Kf) is 1.7 (Kfs = 1.5). It can be assumed that Kb = 1 and the...
A round shaft is being assembled into a round hole and the basic size is 2.0000...
A round shaft is being assembled into a round hole and the basic size is 2.0000 inch.  Suppose both parts can be manufactured to a tolerance of 0.0008 inch and we want a maximum interference of 0.0020 inch to ensure proper functionality. Size the hole and the shaft using unilateral tolerances.  The material condition is MMC and assign tolerances using the Basic Hole System.  Provide all necessary calculations and figures.
A round shaft is being assembled into a round hole and the basic size is 2.0000...
A round shaft is being assembled into a round hole and the basic size is 2.0000 inch.  Suppose both parts can be manufactured to a tolerance of 0.0008 inch and we want a maximum interference of 0.0020 inch to ensure proper functionality. Size the hole and the shaft using unilateral tolerances.  The material condition is MMC and assign tolerances using the Basic Hole System.  Provide all necessary calculations and figures.
A geometric tolerance is the maximum permissible variation of form, orientation, or ________________ of a feature...
A geometric tolerance is the maximum permissible variation of form, orientation, or ________________ of a feature from that indicated or specified on a drawing. location strength size fit
A solid steel shaft, 20 mm in diameter and 1 m long, is placed concentrically inside...
A solid steel shaft, 20 mm in diameter and 1 m long, is placed concentrically inside a hollow duralumin shaft with inside and outside diameters of 30 mm and 33 mm respectively and a length of 500 mm. The ends of the hollow shaft are rigidly fixed to the solid shaft. Determine (a) the torsional stiffness of the composite shaft (b) the maximum torque to which the composite shaft may be subjected if the allowable shear stresses for steel and...
The drive shaft AB of an automobile with 1.7 m long is made of a steel...
The drive shaft AB of an automobile with 1.7 m long is made of a steel having an allowable shear stress τall = 60 MPa and modulus of rigidity G = 80 GPa. Limit angle of twist of the shaft is 0.035 rad. If the outer diameter of the shaft is 65 mm and the engine delivers 180 kW to the shaft when it is turning at 1170 rev/min, determine the minimum required thickness of the shaft’s wall.
Determine whether the given function has a maximum value or a minimum value, and then find...
Determine whether the given function has a maximum value or a minimum value, and then find the value. f(x) = -x2+ 6x - 4
a) An internal combustion engine of 100 horsepower (hp) transmits power to the car wheels of...
a) An internal combustion engine of 100 horsepower (hp) transmits power to the car wheels of an automobile at 600 rev/min (rpm). Neglecting any transmission losses, determine the minimum permissible diameter of the solid circular section steel shaft if the maximum shear stress in the shaft is limited to 75MPa. What will be the resulting angle of twist of the shaft, due to the applied torque, over a length of 1 m? Given that the rigidity modulus, G = 50...
Q2)What would be the maximum aggregate size used for the given mixture properties by using ACI...
Q2)What would be the maximum aggregate size used for the given mixture properties by using ACI Method of Mix Design. 28-day specified concrete strength is 3bMpa, standard deviation is choosen as 3.aMpa and it is required that no more than 1 test result in 200 will fall below the specified strength. Project Title:Detoration of wood column of a commercial building Project summary:Wood deterioration at the lower level of a heavy timber column, which supports five floor levels, was remedied by...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT