Question

The power required to shear a plate 60mm thick for 20sec is 8KW. If the ultimate...

The power required to shear a plate 60mm thick for 20sec is 8KW. If the ultimate strength of plate materials is 4oo Mpa, How wide should the plate be?

Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

please find the solution of above question

rate me high!

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A plate 400mm wide and 0.03 mm thick with strength of 400Mpa is to shear. During...
A plate 400mm wide and 0.03 mm thick with strength of 400Mpa is to shear. During shearing process a 1000mm mean diameter flywheel changes its speed from 220 to 200 rpm. Determine the weight of flywheel to be used.
A single riveted lap joint rivet is made on a thick plate with a diameter of...
A single riveted lap joint rivet is made on a thick plate with a diameter of 20 mm. Determine the strength of the connection, if the pitch of the rivet is 60 mm. Assume ??? = 120 MPa; ? = 90 MPa and ??? = 160 MPa.
How many coulombs are required to plate a layer of chromium metal 0.29 mm thick on...
How many coulombs are required to plate a layer of chromium metal 0.29 mm thick on an auto bumper with a total area of 0.25 m2 from a solution containing CrO2−4? The density of chromium metal is 7.20 g/cm3. Express your answer using two significant figures. Q = nothing C SubmitRequest Answer Part B What current flow is required for this electroplating if the bumper is to be plated in 12.5 s ? Express your answer using two significant figures.
Introduction to Engineering Materials Question: A beam of light hits a 2.48cm thick silicate glass plate...
Introduction to Engineering Materials Question: A beam of light hits a 2.48cm thick silicate glass plate at an angle of 74 degrees (as measured from the normal to the surface of the glass). If the coefficient of linear absorption is 0.027 cm-1 and the index of refraction is 1.488, what fraction of light is passed through the plate. The answer should have three decimals of accuracy. The answer is: 0.847, I need to know the process.
A triple riveted butt joint which is used to connect two 8 mm thick plates. The...
A triple riveted butt joint which is used to connect two 8 mm thick plates. The rivet diameter and the pitch are 10 mm and 50 mm respectively. Determine the efficiency of the riveting system. Assume the rivet material has the same properties of plate material used if need power 1kw velocity 500rpm ultimate stress 680Mpa yield stress 400Mpa shaft diameter50mm   tension=compression
Consider the following observations on shear strength (MPa) of a joint bonded in a particular manner....
Consider the following observations on shear strength (MPa) of a joint bonded in a particular manner. 21.2      40.4      16.4      73.6      36.6      110.0      30.0      4.4      33.1      66.7      81.5   a) What are the values of the fourths? (Enter your answers to two decimal places.) lower fourth     MPa upper fourth     MPa What is the value of fs? = MPa Comment on its features. (Select all that apply.) The variation seems quite large. The data is symmetric. There are outliers. There is a slight...
A steel shaft transmits 20 kW of power at 10 Hz. Determine the smallest safe diameter...
A steel shaft transmits 20 kW of power at 10 Hz. Determine the smallest safe diameter of the shaft if the shear stress τmax is not to exceed 50 MPa and the angle of twist θ is limited to 5°in a length of 4 m. Use G = 70 GPa. Using the relationship θ = TL / IpG in the above problem, again determine the diameter that is necessary to satisfy the requirement of rigidity (remembering to convert θ from...
A glass marble is dropped down an elevator shaft and hits a thick glass plate on...
A glass marble is dropped down an elevator shaft and hits a thick glass plate on top of an elevator that is descending at a speed of 2.00 m/s. The marble hits the glass plate 6.5 m below the point from which it was dropped. If the collision is elastic, how high will the marble rise, relative to the point from which it was dropped?
Calculate the total area of steel required in tension zone for a simply supported beam of...
Calculate the total area of steel required in tension zone for a simply supported beam of 230 mm wide, 406 mm effective depth. The total ultimate factored moment on the beam is 146.76 kN.m. Assume an effective cover for the compression reinforcement as 20 mm. Mu,lim of the section is 130.76 kN.m. Use M25 grade concrete and Fe415 steel. Check for spacing, shear and deflection is not required.
A rectangular metal plate measures 0.14 m long and 0.7 m wide. The plate is heated...
A rectangular metal plate measures 0.14 m long and 0.7 m wide. The plate is heated to a temperature of 1,233 K by passing a current through it. Assuming that it behaves like a blackbody, how much power does the plate radiate under these conditions? Please ensure you're correct, the last person had been wrong.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT