Question

A mild steel shaft transmits 20kw at 200rpm. it carries a central load. it has a...

A mild steel shaft transmits 20kw at 200rpm. it carries a central load. it has a burning moment of 500Nm. Determine the size of the shaft if the available shear stress 42mpa and maximum stress is not to exceed 56mpa

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A steel shaft transmits 20 kW of power at 10 Hz. Determine the smallest safe diameter...
A steel shaft transmits 20 kW of power at 10 Hz. Determine the smallest safe diameter of the shaft if the shear stress τmax is not to exceed 50 MPa and the angle of twist θ is limited to 5°in a length of 4 m. Use G = 70 GPa.
5. A solid steel shaft has a diameter of 200mm. The shaft transmits 550kW at 300r/min....
5. A solid steel shaft has a diameter of 200mm. The shaft transmits 550kW at 300r/min. It is also subjected to a bending moment of 10kNm and an end thrust of 400kN. Find: 5.1 The applied torque 5.2 The applied shear stress 5.3 The applied bending stress 5.4 The stress due to the end thrust Draw a stress element and matching Mohr’s circle clearly showing Both principle stresses and the maximum shear stress at: 5.5 the top of the shaft’s...
A steel shaft transmits 20 kW of power at 10 Hz. Determine the smallest safe diameter...
A steel shaft transmits 20 kW of power at 10 Hz. Determine the smallest safe diameter of the shaft if the shear stress τmax is not to exceed 50 MPa and the angle of twist θ is limited to 5°in a length of 4 m. Use G = 70 GPa. Using the relationship θ = TL / IpG in the above problem, again determine the diameter that is necessary to satisfy the requirement of rigidity (remembering to convert θ from...
Find the outside and inside diameter of a mild steel hollow shaft if with allowable shear...
Find the outside and inside diameter of a mild steel hollow shaft if with allowable shear stress (42 Mpa) with a transmitting torque of (955*10^3 N-mm) take the ratio of inside diameter to outside diameter (0.5)
a) An internal combustion engine of 100 horsepower (hp) transmits power to the car wheels of...
a) An internal combustion engine of 100 horsepower (hp) transmits power to the car wheels of an automobile at 600 rev/min (rpm). Neglecting any transmission losses, determine the minimum permissible diameter of the solid circular section steel shaft if the maximum shear stress in the shaft is limited to 75MPa. What will be the resulting angle of twist of the shaft, due to the applied torque, over a length of 1 m? Given that the rigidity modulus, G = 50...
3. A 2014 T-4 aluminum hollow drive shaft has an outside diameter of 3 in, an...
3. A 2014 T-4 aluminum hollow drive shaft has an outside diameter of 3 in, an inside diameter of 2.9 in, and a length of 10.0 ft. It transmits a power of 120 hp at 300 rpm. Find the following (include units with your answers): a) the maximum torsional shear stress in the shaft (ksi)=   b) the angle of twist (deg)=  
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load of 325 kN. If the compressive stress is 150 MPa, lateral strain for external diameter is is 0.000325 and Poisson’s ratio is 0.3, find the minimum wall thickness required for the column. Also calculate the shear modulus for the material of the column. Take E = 210 GPa.   
The drive shaft AB of an automobile with 1.7 m long is made of a steel...
The drive shaft AB of an automobile with 1.7 m long is made of a steel having an allowable shear stress τall = 60 MPa and modulus of rigidity G = 80 GPa. Limit angle of twist of the shaft is 0.035 rad. If the outer diameter of the shaft is 65 mm and the engine delivers 180 kW to the shaft when it is turning at 1170 rev/min, determine the minimum required thickness of the shaft’s wall.
WITH COMPLETE SOLUTION A welded steel girder having the cross section of two fabricated 280 mm...
WITH COMPLETE SOLUTION A welded steel girder having the cross section of two fabricated 280 mm x 25 mm flange and a 600 mm x 15 mm web plate. The plates are joined by four fillet welds that run continuously for the length of the 6 m span girder. Each weld has an allowable load of 330 kN/m. 1.Determine the maximum allowable shear force V for the girder in kN. 2. Calculate the maximum bending stress of the girder if...
overhanging beam is simply supported at san of 13m and carries of point load of 4000N...
overhanging beam is simply supported at san of 13m and carries of point load of 4000N 3m from right support the left overhangs is 3 m away from left support and has a point load of 5000N. the right overhang is of 4m carrying UDL of 200N per meter for entire rightover . draw shear force and bending moment diagram . calculate the maximum bending moment.