Question

‏A centrifugal pump delivers water against a net head of 14 m and a speed of...


‏A centrifugal pump delivers water against a net head of 14 m and a speed of 1300 rpm. The blade angle is given as 35º. The impeller outlet diameter is 225 mm and outlet width is 50 mm. Determine the discharge of the pump if manometric efficiency is 83%.
Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A centrifugal pump has an impeller of outer diameter, 20 cm and outer width,4 cm. The...
A centrifugal pump has an impeller of outer diameter, 20 cm and outer width,4 cm. The pump delivers a flow of 30 L/s against a head of 10.5 m at an operating speed of 550 rpm. If the hydraulic efficiency of the pump is 85% and the overall efficiency is 80%, determine the impeller outlet vane angle and the power required to run the pump.
Q1/ Centrifugal pump runs at (1200 r.p.m) and the velocity of flow through the impeller is...
Q1/ Centrifugal pump runs at (1200 r.p.m) and the velocity of flow through the impeller is constant (4 m/s). It works with total head of (32m). The vanes are set back at an angle of (30°) at outlet .The outer diameter of the impeller is (600 mm) while the width of outlet is (50mm). Determine 1) work done per second by impeller 2) Vane angle at inlet 3)discharge 4)efficiency
The rotation speed of a centrifugal water pump is 1500 rpm, its flow rate is 15...
The rotation speed of a centrifugal water pump is 1500 rpm, its flow rate is 15 L / s, the rotor diameter is 0.2 m at the outlet, the rotor width at the outlet is 0.01 m and the mechanical efficiency is 0.92. For the fluid entering the rotor in the axial direction, the wing angle is given as 30o at the outlet. What power should be given to the shaft of this pump? (ρwater = 1000 kg / m3)
(d) A centrifugal pump delivers 1000 Ls-1 of water at a head of 3 m and...
(d) A centrifugal pump delivers 1000 Ls-1 of water at a head of 3 m and speed of 60 rpm. Determine the Net Positive Suction Head Required. Answer is [NPSHR = 0.196 m] How do i do this?
A centrifugal pump operating at 1800 rpm with an efficiency of 70% discharges 30 L/s against...
A centrifugal pump operating at 1800 rpm with an efficiency of 70% discharges 30 L/s against a 25-m head and requires 10.5 KW, Assuming that the efficiency remains constant, estimate the discharge, head and power if the speed is reduced to 1500 rpm.
A centrifugal pump discharges 300 GPM through an 8-inch diameter impeller. The fluid leaves the impeller...
A centrifugal pump discharges 300 GPM through an 8-inch diameter impeller. The fluid leaves the impeller with a tangential velocity of 17 ft/sec. If water, @ 68°F, enters the impeller via radial flow (I.E. no whirl), and the inner radius and thickness of the impeller are 1.5-inches. (Assume a constant thickness of the impeller) and if the pump speed is 1750 rpm, with a head loss of 3.5-feet. What is the Torque on the shaft?
1.       A centrifugal pump running at 2950 rpm under test at peak efficiency gave the following...
1.       A centrifugal pump running at 2950 rpm under test at peak efficiency gave the following results: Effective head H= 75m of water, rate of flow Q= 0.05 m3/s, overall efficiency h= 76%. A dynamically similar pump is to operate at a corresponding point of its characteristic when delivering 0.5 m3/s through a pipe 800m long and 1m diameter for which the friction coefficient f =0.05. The pipe discharges 90m above reservoir level. Determine the rotational speed at which the...
pump was manufactured to couple directly to a 15 hp electric motor running at 1450 rpm...
pump was manufactured to couple directly to a 15 hp electric motor running at 1450 rpm delivering 850 liter/min against a total head 40 m. It is desired to replace the motor by a diesel engine with 1,000 rpm speed and couple it directly to the pump. Find the probable discharge and head developed by the pump Also find the hp of the engine that would be employed, then calculate the pump efficiency (η) for pumping of water, and the...
The characteristics of a centrifugal pump that is used to pump water (998 kgm-3 , 1.14×10-3...
The characteristics of a centrifugal pump that is used to pump water (998 kgm-3 , 1.14×10-3 Nsm-2 ) from one reservoir to another are given in the table below. The difference between the water levels is 3 m. A 840 m long, 0.15 m diameter pipe with absolute roughness of 6×10-6 m joins the two reservoir. Determine the (a) best efficiency point, (b) operating point, (c) operating efficiency and the (d) power adsorbed when the average velocity in the pipe...
Ten turbines are installed in a hydroelectric power station, each with a diameter of 4.5 m...
Ten turbines are installed in a hydroelectric power station, each with a diameter of 4.5 m impeller and each generating a mechanical power of 54 MW at 107 rpm and with an efficiency of 93.8%, for a net head of 65 m. A) Determine the specific speed of each turbine in dimensionless form and in units of the American system. B) What type of turbine should have been selected? Justify your answer. B) Calculate the flow that passes through each...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT