Question

A cylindrical tank is made of A36 steel and has an inner diameter of 1.5 meters....

A cylindrical tank is made of A36 steel and has an inner diameter of 1.5 meters. Using Maximum Shear Stress Theory and a Factor of Safety of 2 with respect to the yield, determine the minimum wall thickness (mm) required:

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A cylindrical storage tank contains liquefied propane under a pressure of 1.5 MPa (gage pressure P=1.5...
A cylindrical storage tank contains liquefied propane under a pressure of 1.5 MPa (gage pressure P=1.5 MPa) and is subjected to an axial force F=60 kN. Knowing that the tank has an inner diameter of 320 mm and a wall thickness of 3 mm, find the principal stresses and determine the maximum shear stress.
Select right answer. A rotating steel flat disk has 200 mm inner diameter and 300 mm...
Select right answer. A rotating steel flat disk has 200 mm inner diameter and 300 mm outer diameter. If the maximum shear stress is to not exceed 200 MPa the allowable speed in rpm is around
The drive shaft AB of an automobile with 1.7 m long is made of a steel...
The drive shaft AB of an automobile with 1.7 m long is made of a steel having an allowable shear stress τall = 60 MPa and modulus of rigidity G = 80 GPa. Limit angle of twist of the shaft is 0.035 rad. If the outer diameter of the shaft is 65 mm and the engine delivers 180 kW to the shaft when it is turning at 1170 rev/min, determine the minimum required thickness of the shaft’s wall.
a cylindrical pressure vessel with an outside diameter of 1000 mm is constructed be spirally wrapping...
a cylindrical pressure vessel with an outside diameter of 1000 mm is constructed be spirally wrapping a 15 mm thick steel plate and butt-welding the mating edges of the plate, the butt-welded seams form an angle of 30 with a transverse plane through the cylinder as shows . if the allowable normal stress perpendicular to the weld and the allowable shear stress parallel to the weld are 40 MPa and 15 MPa a respectively, determine the permissible internal pressure in...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load of 325 kN. If the compressive stress is 150 MPa, lateral strain for external diameter is is 0.000325 and Poisson’s ratio is 0.3, find the minimum wall thickness required for the column. Also calculate the shear modulus for the material of the column. Take E = 210 GPa.   
A hollow cylinder that is constructed of A36 steel (yield strength 36 ksi, and modulus E=29E6...
A hollow cylinder that is constructed of A36 steel (yield strength 36 ksi, and modulus E=29E6 psi), has an inner diameter of 4 inches and a wall thickness of .1 inches. It is subjected to an internal pressure of p=100 psi. in addition to the applied loads of 500 lb axial tension and 70 lb inch torsion. does yielding occur?
A cylindrical steel pressure vessel 30 cm in diameter and 1.5 cm thick contains a small...
A cylindrical steel pressure vessel 30 cm in diameter and 1.5 cm thick contains a small surface crack, oriented normally in the direction of the hoop stress. (a) Confirm that there is a leak condition before rupture, since the container experiences a cyclic gas pressure between 40 and 50 MPa and the fracture resistance of the material is 180 MPa√m. (b) At the point where the crack broke the wall thickness, calculate the rate of advance of the fatigue crack....
Design a cylindrical tank for compressed air that will be used to provide remote service for...
Design a cylindrical tank for compressed air that will be used to provide remote service for truck tire repair. The air pressure will be 300psi. the minimum internal diameter for the tank is to be 24 in. use AISI 1040 cold-drawn steel & a design factor of 8 based on the ultimate strength. Check the final design for a maximum pressure of 900 psi by computing the design factor based on the yield strength.
A cylindrical oil storage tank is 50 meters tall and has a diameter of 40 meters...
A cylindrical oil storage tank is 50 meters tall and has a diameter of 40 meters is sitting on a concrete pad.. Do NOT change system of units! a) What is the pressure inside the tank at 10 meters above the concrete pad? b) What is the total force acting on the bottom of the tank? c) What is the total force acting on the side of the tank? Keep your answer in decimal form and to 1 decimal place....
A composite member is made of a hollow steel pipe with an inner diameter of 12”...
A composite member is made of a hollow steel pipe with an inner diameter of 12” and wall thickness 1”. The hollow steel pipe is filled with concrete and subjected to a compressive force of 120,000 lbs. The member length is 25’. The modulus of elasticity of concrete and steel are Ec = 3,600,000 psi and Es = 30,000,000 psi, respectively. Calculate the axial and compressive loads resisted by the steel and concrete. Fconcrete = 45000 lbs ; Fsteel =...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT