Question

A simple gas turbine plant working on the ideal constant pressure cycle. Air is taken into...

A simple gas turbine plant working on the ideal constant pressure cycle. Air is taken into the compressor at 1 bar, 20.2 deg C and delivered at 7.2 bar. If the temperature at the turbine inlet is 765 deg C. Calculate the ideal thermal efficiency.

Homework Answers

Answer #2

The answer is boxed and steps are shown clearly. Thank You and stay safe.

answered by: anonymous
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
An open cycle gas turbine using a regenration arrangement. The air enters the compressor at 1...
An open cycle gas turbine using a regenration arrangement. The air enters the compressor at 1 bar 288 K and is compressed to 10 bar with compressor effieciency= 0.85. The air is heated in regenerator and then enter in combustion chamber its temperature is raised ny 1700 k and during the process the pressure falls by 0.2 bar. The air is then expanded in the turbine and passes to regenerator which has 0.75 effectiveness and cause a pressure drop of...
Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 =...
Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 = 520°R. The isentropic efficiencies of the compressor and turbine are 83 and 87%, respectively. The compressor pressure ratio is 16 and the temperature at the turbine inlet is 2500°R. The volumetric flow rate of the air entering the compressor is 9000 ft3/min. Use an air-standard analysis. Determine all temperatures at each state. A) Determine the net power developed, in Btu/h. (Already did this part,...
A single shaft gas turbine engine receives air at atmospheric conditions of 14.7 psia and 80...
A single shaft gas turbine engine receives air at atmospheric conditions of 14.7 psia and 80 degrees F. The compressor discharge pressure is 103psia and the compressor efficiency is 87%. The turbine inlet temperature is 1980 degrees F and the exhaust temperature is 1173 degrees F. Assume a 3 psi pressure drop in the combustion chamber and that inlet and exhaust ducts losses are both 27.7 inches of water. Find: a) Sketch the system and label the state point locations...
A steam power plant operates on the simple ideal rankine cycle between the pressure limits of...
A steam power plant operates on the simple ideal rankine cycle between the pressure limits of 50 kPa and 20 MPa, with a turbine inlet temperature of 600 Degree C. Disregarding the pump work, then: (a) Show the T-S diagram of the entire cycle. (b) Solve the total heat (kJ/kg) input for the cycle. (c) Solve the total heat (kJ/kg) reject by the cycle. (d) Solve the thermal efficiency of this plant.
Consider a combined gas-steam power cycle. The topping cycle is a simple Brayton cycle that has...
Consider a combined gas-steam power cycle. The topping cycle is a simple Brayton cycle that has a pressure ratio of 7. Air enters the compressor at 15 ºC at a rate of 10 kg/s and the gas turbine at 950 ºC. The bottoming cycle is a reheat Rankine cycle between the pressure limits of 6 MPa and 10 kPa. Steam is heated in a heat exchanger at a rate of 1.15 kg/s by the exhaust gases leaving the gas turbine,...
A gas turbine power plant which will be powered by a heat source having a temperature...
A gas turbine power plant which will be powered by a heat source having a temperature of at least 840·C is to be designed with a pressure ratio of 4. Regeneration is to be incorporated into the power piant design and it is expected that the regenerator effectiveness will be at least 90%. It is intended that the working fluid will enter the compressor at 100 kPa and 15°C. Using air-standard cycle analysis, calculate the minimum thermal efficiency of the...
A gas turbine power plant operates on a Brayton cycles has a pressure ratio of 7....
A gas turbine power plant operates on a Brayton cycles has a pressure ratio of 7. Air enters the compressor at 300 K. The energy in the form of heat is transferred to the air in the amount of 950 kJ/kg. Using a variable specific heat for air and assuming the compressor isentropic efficiency is 83 percent and turbine isentropic efficiency is 85 percent. Determine the followings: (i) The highest temperature in the cycle (ii) The net work output, in...
the ideal air standard Brayton cycle consists of the following processes: 1-2 isentropic compression through a...
the ideal air standard Brayton cycle consists of the following processes: 1-2 isentropic compression through a pressur ratio rp =p2/p1 2-3 heat addition at constant pressure untill the pressure is p3 3-4 isentropic expansion to the initial pressure 4-1 heat rejection at constnt pressure A- show that the cycle efficiency for this cycle is B-Air enters compressor of a gas turbine at 100kpa and 250c.for a pressure ratio of 5 and a maximum temp of 8500c , determine the thermal...
Steam enters the turbine of an ideal Rankine cycle power plant with a pressure of 12.5...
Steam enters the turbine of an ideal Rankine cycle power plant with a pressure of 12.5 MPa and a temperature of 600°C and expands adiabatically to condenser pressure equal to 30 kPa . Please answer the following: a. Represent the cycle on a T-s diagram, indicate the values of the isobars and temperature and entropy on the axes. b. Compute the thermal efficiency for this cycle.
A small gas turbine has a pressure ratio of 9.5, and compressor efficiency of 88%. Overall...
A small gas turbine has a pressure ratio of 9.5, and compressor efficiency of 88%. Overall thermal efficiency is 37%. Ambient conditions are 27oC, 1 bar. Air leaving the compressor passes through a regenerator where it is heated by the exhaust gases leaving the turbine. If the maximum temperature in the cycle is 1300oC and the exhaust gases leave the turbine at 700oC, calculate the effectiveness of the regenerator, giving your answer to the nearest integer percentage. Use standard aircycle...