Question

A 15 cm x 15 cm circuit board dissipating 20 W of power uniformly is cooled...

A 15 cm x 15 cm circuit board dissipating 20 W of power uniformly is cooled by air, which approaches the circuit board at 20°C with a velocity of 6 m/s. Disregarding any heat transfer from the back surface of the board, determine the surface temperature of the electronic components at the end of the board. Assume the flow to be turbulent since the electronic components are expected to act as turbulators. Assume a film temperature of 27°C.

Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
The electronic components of a computer are cooled by air flowing through a fan mounted at...
The electronic components of a computer are cooled by air flowing through a fan mounted at the inlet of the electronics enclosure. At steady state, air enters at 20.2∘C and 100 kPa. For noise control, the velocity of the entering air cannot exceed 1.09 m/s. For temperature control, the temperature of the air at the exit cannot exceed 33.2∘. The electronics use 83.3 W of power and the fan uses 19.4 W (assume that the power dissipated by the electronics...
An Integrated Circuit (IC) internally generates 1.8 Watts of heat energy which must be dissipated to...
An Integrated Circuit (IC) internally generates 1.8 Watts of heat energy which must be dissipated to ensure its reliable operation. A heat sink is attached to the IC to transfer heat away by convection. The dimensions of the flat heat sink are 6.6 cm by 5.3 cm. Assuming only one side of the heat sink is exposed to the air, the surrounding air temperature is at 25 ºC and the heat transfer co-efficient of the heat sink is 49 W/(m2.K)....
A can of soft drink, 12-cm high and 6-cm diameter, is initially at 20°C. It is...
A can of soft drink, 12-cm high and 6-cm diameter, is initially at 20°C. It is placed in a refrigerator where the air is at 0°C. The convective heat transfer coefficient associated with the outer surface of the can is 10 W/m2 °C. Assuming the properties of the drink to be those of water and that the heat capacity of the container is negligible, estimate the time taken for the temperature of the drink to reach 5°C. USING EES PLEASE
A long 10 cm × 20 cm rectangular cross section steel bar ݇ k= 63.9 W/mK...
A long 10 cm × 20 cm rectangular cross section steel bar ݇ k= 63.9 W/mK and alpha=18.8*10^-6 m^2 /s was heated to an initial temperature of 450°C. The steel bar is allowed to cool in a room with a temperature of 25°C and convection heat transfer coefficient of 25 W/m^2 K. The bottom surface of the bar is insulated while the other surfaces are exposed to convection. With a uniform nodal spacing of 5 cm, determine the duration required...
The walls of an oven are made from steel sheets with insulating board between them of...
The walls of an oven are made from steel sheets with insulating board between them of thermal conductivity 0.18 J m-1 s-1 °C-1. If the maximum internal temperature in the oven is 300°C and the outside surface of the oven wall must not rise above 50°C, estimate the minimum necessary thickness of insulation assuming surface heat transfer coefficients to the air on both sides of the wall are 15 J m-2 s-1 °C-1. Assume the room air temperature outside the...
a) A 12 mm diameter mild steel sphere (k = 42.5 W/m K) is exposed to...
a) A 12 mm diameter mild steel sphere (k = 42.5 W/m K) is exposed to cooling airflow at 27 0C resulting in the convective coefficient, h = 114 W/ m2 K. The relevant properties of mild steel are given as follows: Density , /7850 2 mkg  Specific heat K kgJc p / 475 and thermal diffusivity hr m /043.0 2  Determine: (i) Time required to cool the sphere (lumped parameter system) from 540 0C to 950C. [7...
Homework-9 Due: Q) A fuel plate is fabricated from 0.3 cm thick 1.5% enriched uranium. The...
Homework-9 Due: Q) A fuel plate is fabricated from 0.3 cm thick 1.5% enriched uranium. The cladding is 0.25 mm 304 stainless steel. The coolant saturation temperature is 260 oC. The average thermal neutron flux is 2.5 X 1014 neutrons/cm2 /s. The surface temperature of the clad is 350 oC. Assume any missing data to answer the following questions:. 1) Write an expression of the heat generated per unit volume 2 What is the heat flux at the surface of...
Air is to be cooled in the evaporator section of a refrigerator by passing it over...
Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.8-m-long tubes inside which the refrigerant is evaporating at −20°C. Air approaches the tube bank in the normal direction at 0°C and 1 atm with a mean velocity of 9 m/s. The tubes are arranged in-line with longitudinal and transverse pitches of SL  =  ST  = 1.5 cm. There are 25 rows in the flow direction with 15 tubes...
Water at 15°C enters a tube of 2 cm of diameter with flow rate 3953 kg/h....
Water at 15°C enters a tube of 2 cm of diameter with flow rate 3953 kg/h. Assume the ratio L/D>10, and the wall temperature is constant at 80-C. The outlet temperature is 50°C The properties of water at the film temperature are density rho = p = 985 kg/m3, specific heat Cp = 4180 J/kgk, conductivity k = 0.651 W/mK, dynamic viscosity mu= u = 4.71 × 10- kg/ms, At the wall temperature of 80°C we have dynamic viscosity muw=...
A steel sphere has an inner volume of 4 liters and weighs 15 lbs when empty....
A steel sphere has an inner volume of 4 liters and weighs 15 lbs when empty. it also has a hole in the top that is 3.33 mm in diameter. the sphere is half filled with ice and the other half is filled with air. the whole system starts at STP. (you do not need the specific heat of air ) 1. what is the total energy needed to raise this system to 100 degrees C? A 999 W heater...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT