Question

6) Air at 288 K and 275 kPa abs enters a pipe and is flowing in...

6)

Air at 288 K and 275 kPa abs enters a pipe and is flowing in isothermal compressible flow in a

commercial pipe having an ID of 0.080 m. The length of the pipe is 60 m. The mass velocity at the

entrance to the pipe is 165.5 kg/m2 · s. Assume 29 for the mol

ecular weight of air. Calculate the

pressure at the exit.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Air enters a length of constant area pipe with p1 = 490 kPa (abs), T1 =...
Air enters a length of constant area pipe with p1 = 490 kPa (abs), T1 = 450 K, and V1 = 130 m/s. The diameter of the pipe is 0.1 m. If 480 kW of energy is added to the air by frictionless heat transfer between sections (1) and (2), determine p2, T2, and V2.
1. Air at a pressure of 101 kPa and temperature of 288 K enters an axial...
1. Air at a pressure of 101 kPa and temperature of 288 K enters an axial compressor stage with a velocity of 170 m/s. There are no guide vanes, so the air enters in the axial direction only. When traveling through the rotor, the air turns 15 degrees. This means the angle of the relative velocity with respect to the axis is 15 degrees greater when entering the rotor than when it leaves. The rotor spins at 8000 rpm and...
Air at a pressure of 101 kPa and temperature of 288 K enters an axial compressor...
Air at a pressure of 101 kPa and temperature of 288 K enters an axial compressor stage with a velocity of 170 m/s. There are no guide vanes, so the air enters in the axial direction only. When traveling through the rotor, the air turns 15 degrees. This means the angle of the relative velocity with respect to the axis is 15 degrees greater when entering the rotor than when it leaves. The rotor spins at 8000 rpm and has...
Methane gas is being pumped through a 305-m length of 52.5-mm-ID steel pipe at the rate...
Methane gas is being pumped through a 305-m length of 52.5-mm-ID steel pipe at the rate of 41.0 kg/(m2 · s). The inlet pressure is p1 = 345 kPa abs. Assume isothermal flow at 288.8 K. p2 = 298.4 kPa. What is the velocity (V2) at the end of the pipe? The viscosity is 1.04 × 10?5 Pa · s. (Answer V2= 20.62 m/s, show all work)
compressible flow: A subsonic flow of air passes through a pipe of 2.5-cm diameter which is...
compressible flow: A subsonic flow of air passes through a pipe of 2.5-cm diameter which is choked at the exit. At the pipe inlet, the stagnation pressure is 700 kPa and the stagnation temperature is 330 K. If f¯ = 0.022 and the pipe length is 12 m, what will be the mass flow rate through the pipe, in kg/sec?
1) A nozzle is a device for increasing the velocity of a steadily flowing stream of...
1) A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (i) Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume...
Pure nitrogen at 160°C and 2 atm enters a cylinder whose inner walls are coated with...
Pure nitrogen at 160°C and 2 atm enters a cylinder whose inner walls are coated with naphthalene. The nitrogen flow is turbulent. The Dittus-Boelter relation for turbulent flow heat transfer in a pipe is Nu = 0.023Re^0.8Pr0.4 The velocity through the 6 cm diameter tube is 10 m s-1. (a) Derive an equation relating concentration of naphthalene to tube length; (b) What tube length would be necessary to obtain a naphthalene mole fraction of 0.05 in the exit stream? Additional...