Question

Suppose an OTEC system using the difference in temperature between 25 C water at the ocean...

Suppose an OTEC system using the difference in temperature between 25 C water at the ocean surface and 5 C water several hundred meters below the water surface to power a Rankine power engine.

What is the maximum efficiency of the system?

If the system runs at 40% of Carnot efficiency, what flow rate of water through the system would be needed to generate 1 MW of electrical power? (density of seawater is 1000 kg/m3 and specific heat is 4.2 kJ/kg.K)

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Ocean Thermal Energy Conversion (OTEC) generates electricity using the difference between the temperatures at the surface...
Ocean Thermal Energy Conversion (OTEC) generates electricity using the difference between the temperatures at the surface of the ocean, where the water is warm, and far below the surface, where the water is cool. A test system off Hawaii operated between temperatures of 28 °C (the water temperature at the surface) and 5 °C (the temperature far below the surface), and operated with an efficiency of 2.3%. (a) What is the theoretical maximum efficiency we could expect from this system?...
In the water behind 110m high dm the temperature difference between the water's surface and the...
In the water behind 110m high dm the temperature difference between the water's surface and the bottom is 10C. The constant-colume het capacity per unit mass is 4.2kJ/kg/C. The temperature at the water's surface is 22C. a) Compute how much energy per unit mass could be obtained by extracting heat form the water. Assume the heat extracted in a process that has the same efficiency as a Carnot engine. b) Compute the energy per unit mass that could be obtained...
A water drop slung onto a skillet with a temperature between 100°C and 200°C will remain...
A water drop slung onto a skillet with a temperature between 100°C and 200°C will remain a liquid for about 1 second. However, if the skillet is much hotter the drop can last several minutes. This is due to the Leidenfrost Effect, named after an early investigator (circa 1756). The longer lifetime is due to the support of a thin layer of air and water vapor that separates the drop from the metal (by a distance L, as shown in...
c (water) = 4190 j/kg•K density of water = 1000 kg/m^3 In Wakanda, at the Vibranium...
c (water) = 4190 j/kg•K density of water = 1000 kg/m^3 In Wakanda, at the Vibranium Institute of Energy Research, the sister of the Black Panther, Shuri has found a way to generate energy from the gradient in temperature of Lake Malawi. At some large depth the temperature of the water is 7.2 degrees C while at the surface it is 26.8 degrees C. (a) The maximum theoretical efficiency of the research power plant is? (b) It is hoped that...
1) A nozzle is a device for increasing the velocity of a steadily flowing stream of...
1) A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (i) Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume...
Temperatures of gases inside the combustion chamber of a four-stroke automobile engine can reach up to...
Temperatures of gases inside the combustion chamber of a four-stroke automobile engine can reach up to 1000°C. To remove this enormous amount of heat, the engine utilizes a closed liquid-cooled system which relies on conduction to transfer heat from the engine block into the liquid and then into the atmosphere by flowing coolant around the outside surface of each cylinder. Assume you have a 6-cylinder engine, and each cylinder has a diameter of 9.00 cm and height of 11.6 cm...
1. Calculate the thermoeconomic cost of the produced electricity using the internal combustion device described in...
1. Calculate the thermoeconomic cost of the produced electricity using the internal combustion device described in homework 7. with and without the heat exchanger. Use the results you calculated to answer this question. This question is focusing on the thermoeconomic costs. The electricity is produced for 10 hours a day, five days per week during a one year cycle. The following cost information is given for the internal combustion device. The cost of the device is $125,000 and it has...
A local coal fired 200 megawatt electrical generating plant has a thermal efficiency of 30% and...
A local coal fired 200 megawatt electrical generating plant has a thermal efficiency of 30% and a nuclear 150 megawatt electrical generating plant has a thermal efficiency of 25%. a. Calculate the waste heat emitted by each (in megawatts) b. If the cooling water used for the nuclear plant were required to only rise in temperature by 2o C after it absorbs the waste heat, how much water per hour would be required to cool the nuclear plant (in cubic...
A grey body is one whose absorptivity 1. does not vary with temperature and wavelength of...
A grey body is one whose absorptivity 1. does not vary with temperature and wavelength of the incident ray 2. is equal to its emissivity 3. varies with temperature 4. varies with wavelength of the incident ray A liquid is in equilibrium with its vapor at its boiling point. On an average, the molecules in the liquid and gaseous phases have equal 1. potential energy. 2. kinetic energy. 3.temperature. 4. intermolecular forces of attraction. A liquid of density 1000 kg/m3...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT