Question

A Diesel cycle engine is analyzed using the **air standard
method**. Given the conditions at state 1, compression ratio
(r), and cutoff ratio (rc) determine the efficiency and other
values listed below.

Note: The gas constant for air is R=0.287 kJ/kg-K.

--Given Values--

T1 (K) = 322

P1 (kPa) = 120

r = 11.5

rc = 1.6

Specific internal energy (kJ/kg) at state 1: 229.86

Relative specific volume at state 1= 520.52

Relative specific volume at state 2= 45.26

Temperature (K) at state 2= 817.4

Pressure (kPa) at state 2 = 3503.1

Specific enthalpy (kJ/kg) at state 2 = 841.12

Temperature (K) at state 3 = 1307.84

Pressure (kPa) at state 3 = 3503.1

Enthalpy (kJ/kg) at state 3 = 1404.3

1. Determine the relative specific volume at state 3.

2. Determine the relative specific volume at state 4.

3. Determine the temperature (K) at state 4

4. Determine the pressure (kPa) at state 4.

5. Determine the specific internal energy (kJ/kg) at state 4.

6. Determine the net work per cycle (kJ/kg) of the engine.

7. Determine the heat addition per cycle (kJ/kg) of the engine

8. Determine the efficiency (%) of the engine

Answer #1

answered by: anonymous

A Diesel cycle engine is analyzed using the air standard
method. Given the conditions at state 1, compression ratio
(r), and cutoff ratio (rc) determine the efficiency and other
values listed below.
Note: The gas constant for air is R=0.287 kJ/kg-K.
--Given Values--
T1 (K) = 322
P1 (kPa) = 120
r = 11.5
rc = 1.6
Specific internal energy (kJ/kg) at state 1: 229.86
Relative specific volume at state 1= 520.52
Relative specific volume at state 2= 45.26
Temperature...

A diesel engine operates at 3000 rpm on a standard Diesel cycle
has a compression ratio of 14. The state of air at the beginning of
the compression process is 98 kPa and 24 ?C. The maximum
temperature in the cycle is not exceed 1850 ?C. Assume diesel fuel
has a heating value of 45 MJ/kg. Use the PG model.
a) Determine the thermal efficiency.
b) Determine the specific fuel consumption. (kg/kJ)
c) What-if Scenario: What would the
thermal efficiency...

1) An air-standard Otto cycle has a compression ratio of 9. At
the beginning of the compression process, the temperature is 20°C,
and the pressure is 100 kPa. The heat added is 500 kJ/kg. Determine
the cycle efficiency, work output, and the heat rejected
2) An air-standard Otto cycle operates with a minimum
temperature of 300 K and a maximum temperature of 1700 K. The
compression ratio of the cycle is 7. At the beginning of the
compression process, the...

10) An air-standard Otto cycle has a compression ratio of 9. At
the beginning of the compression process, the temperature is 20°C,
and the pressure is 100 kPa. The heat added is 500 kJ/kg. Determine
the cycle efficiency, work output, and the heat rejected.
11)An air-standard Otto cycle operates with a minimum
temperature of 300 K and a maximum temperature of 1700 K. The
compression ratio of the cycle is 7. At the beginning of the
compression process, the pressure...

Consider a cold air-standard Diesel cycle. At the beginning of
compression, 102 kPa, and 300 K. The mass of air is 0.120 kg, the
compression ratio is 16, and the cut-off ratio is 2.0
For a cold air-standard analysis use the following values: cp =
1.005 kJ/kgK, cv = 0.718 kJ/kgK, k=1.40, M=28.97 kg/kmol.
Determine the following :
(a) pressure at end of compression stroke, in kPa
(b) temperature at end of compression stroke, in K
(c) maximum temperature in...

An ideal Otto cycle engine, an ideal Diesel cycle engine, and a
Stirling engine all have a maximum volume of 1 liter. The volume at
the end of combustion for the Otto and Diesel engines is 0.1 liter.
The minimum volume for the Stirling engine is 0.1 liter. All three
engines operate with air initially at 100 kPa, and have a minimum
temperature of 300 K and a maximum temperature of 1200 K. Determine
how much work is done for...

Use cold-air-standard analysis with the fluid modeled as an
ideal gas with R=0.287 kJ/kg-K and constant k=1.4. Neglect changes
in kinetic and potential energy. Consider a SSSF of air at 300 K
and 100 kPa entering the compressor of a Simple Brayton Cycle Gas
Turbine powerplant. The cycle pressure ratio is 40 and maximum
cycle temperature is 1800 K. For compressor isentropic efficiency
of 82% the compressor work input per unit mass = __ kJ/kg (enter
the nearest positive integer...

Your new engine design consists of a piston cylinder
arrangement. The engine operates with mostly air and a small amount
of fuel. The system undergoes a cycle. The initial Pressure and
temperature are p1= 1bar and T1= 27°C. The system undergoes a power
cycle consisting of the following process:
Process
1-2
constant volume to a pressure, P2 of 4 bars
Process
2-3
expansion of pv=constant
Process 3-1
constant-pressure compression
Draw the system and pv diagrams
If P2 is 4...

Consider an ideal Ericsson cycle with air as the working fluid
executed in a steady-flow system. Air is at 27°C and 110 kPa at the
beginning of the isothermal compression process, during which 150
kJ/kg of heat is rejected. Heat transfer to air occurs at 950 K.
The gas constant of air is R = 0.287 kJ/kg·K.
a.)The maximum pressure in the cycle is? kPa
b.)The net work output per unit mass of air is? kJ/kg
c.)The thermal efficiency of...

At the beginning of the compression process of an air-standard
Otto cycle, p1 = 1 bar and T1 = 300 K. The compression ratio is 6
and the heat addition per unit mass of air is 1500 kJ/kg.
Determine: (a) the maximum temperature of the cycle, in K. (b) the
net work, in kJ/kg. (c) the percent thermal efficiency of the
cycle. (d) the mean effective pressure, in kPa.

ADVERTISEMENT

Get Answers For Free

Most questions answered within 1 hours.

ADVERTISEMENT

asked 1 minute ago

asked 2 minutes ago

asked 3 minutes ago

asked 5 minutes ago

asked 12 minutes ago

asked 13 minutes ago

asked 13 minutes ago

asked 13 minutes ago

asked 17 minutes ago

asked 17 minutes ago

asked 17 minutes ago

asked 17 minutes ago