Question

A 1.5cm inside diameter tube has water flowing in it at a flow rate such that...

A 1.5cm inside diameter tube has water flowing in it at a flow rate such that the Reynolds number is 50,000. The water enters the tube at 10oC and the tube wall temperature is maintained at 15oC higher than the average water bulk temperature. Calculate:

a) the amount of heat transfer required to achieve a 10oC increase in water temperature (in W)

b) the length of the tube to achieve this amount of heat transfer (in meters)

Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Water at 15°C enters a tube of 2 cm of diameter with flow rate 3953 kg/h....
Water at 15°C enters a tube of 2 cm of diameter with flow rate 3953 kg/h. Assume the ratio L/D>10, and the wall temperature is constant at 80-C. The outlet temperature is 50°C The properties of water at the film temperature are density rho = p = 985 kg/m3, specific heat Cp = 4180 J/kgk, conductivity k = 0.651 W/mK, dynamic viscosity mu= u = 4.71 × 10- kg/ms, At the wall temperature of 80°C we have dynamic viscosity muw=...
A parallel flow heat exchanger is used to transfer heat from hot water at 80oC, flowing...
A parallel flow heat exchanger is used to transfer heat from hot water at 80oC, flowing at 5 L/min to cold water at 15oC which is flowing at a rate of 15 L/min. The overall heat transfer coefficient is 2000 W/m2oC and the area is 0.2m2. Calculate the heat transfer rate, the outlet temperature of the cold water.
A 10-mm diameter tube has a maintained surface temperature of 200°C. Engine oil enters the tube...
A 10-mm diameter tube has a maintained surface temperature of 200°C. Engine oil enters the tube at 70°C at a flow rate of 0.5 kg/s and exits at 105°C. Find the length, in m, of the tube and well as the corresponding heat transfer rate, in W. Assume fully developed flow and use the Dittus–Boelter equation to calculate the average Nusselt number. q = .    L =
Pressurized Water is heated in a thin tube with a diameter of 60 mm. water enters...
Pressurized Water is heated in a thin tube with a diameter of 60 mm. water enters with a mass flow rate of 0.01 kg/s and an inlet temperature of 20°C. a uniform heat flux of 2000 W/m2 is applied to the tube. What is the required length of the tube to obtain an exit temperature of 80°C for the water? If the water reaches 80°C at the outlet, what is the surface temperature of the tube at the outlet?
Mercury at an inlet temperature of 75 °C flows through a 2 cm inside diameter tube...
Mercury at an inlet temperature of 75 °C flows through a 2 cm inside diameter tube at a flow rate of 1.5 kg/s. This tube is part of a nuclear reactor in which heat can be generated uniformly at any desired rate by adjusting the neutron flux level. Determine convection heat transfer coefficient, and the heat flux required for a 1.5 m length of tube required to raise the temperature of the mercury to 275 °C. Also determine if mercury...
Water at a flow rate of 60 kg/s enters the shell-side of a baffled shell-and-tube heat...
Water at a flow rate of 60 kg/s enters the shell-side of a baffled shell-and-tube heat exchanger at 35 °C and leaves at 25 °C. The heat will be transferred to 150 kg/s of raw water coming from a supply at 15 °C. You are requested to design the heat exchanger for this purpose. A single shell and single tube pass is preferable. The tube diameter is ¾ in. (19 mm outer diameter with 16 mm inner diameter) and tubes...
Steam at its saturation temperature of 65°C is condensing on the outside of a tube with...
Steam at its saturation temperature of 65°C is condensing on the outside of a tube with outside diameter 2.5cm and length 3m. The tube is maintained at 35°C by flow of cooling water through it. Calculate the average heat transfer coefficient over the tube length and the rate of condensate flow at the bottom of the tube. Physical properties can be found in data tables. Find the heat transfer coefficients for the vertical and horizontal tubes using both the Nusselt...
A smooth tube 5 cm in diameter and 450 cm in length is placed inside another...
A smooth tube 5 cm in diameter and 450 cm in length is placed inside another tube larger in diameter. Air enters the smaller diameter tube at a pressure of 5 bars, a mean temperature of 16 oC , and at a flow rate of 29 gm/s. saturated steam at 1.523 bar in the annulus between the two tubes condenses on the surface 0f the inside tube find: The outlet temperature of air The outlet pressure of air The mass...
In a warehouse, a cold room that is maintained at 10oC has a wall made of...
In a warehouse, a cold room that is maintained at 10oC has a wall made of two layers of materials. The inner layer has a thickness of 2 cm and a thermal conductivity of 0.1 W/mK. The outer layer, which is 4 cm thick, has a thermal conductivity of 0.04 W/mK. The temperature of the outside ambient is 30oC . The convective heat transfer coefficients on the outside and the inside of the wall are 40 W/m2K and 20 W/m2K...
Liquid water flows in a long pipe of internal diameter of D = 0.01 m at...
Liquid water flows in a long pipe of internal diameter of D = 0.01 m at a mean velocity of V = 0.065 m/s. The pipe is maintained at a constant and uniform surface temperature. Assume the flow is both hydrodynamically and thermally fully developed. For simplicity, evaluate the properties of water at 300 K. Calculate the convective heat transfer coefficient of the flow inside the pipe in W/m2K?
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT