Question
Estimate the size of plastic tubing that should be selected if 0.002 m3/s of water is...
Estimate the size of plastic tubing that should be selected if 0.002 m3/s of water is to be transported such that the pressure drop does not exceed 200 kPa in a 100-m horizontal section. e=0, smooth pipe. Find the diameter of the pipe.
Homework Answers
Answer #1
Not the answer you're looking for?
Similar Questions
Water flows through a horizontal pipe at a rate of 2.3 m3/s. A pressure gauge placed...
Water flows through a horizontal pipe at a rate of 2.3 m3/s. A
pressure gauge placed on a 40 cm diameter section of the pipe reads
210.3 kPa. What is the gauge pressure in a section of pipe where
the diameter is constricted to 35 cm and what has caused this
change in pressure?
A horizontal pipe contains water at a pressure of 100 kPa flowing with a speed of...
A horizontal pipe contains water at a pressure of 100 kPa
flowing with a speed of 2.0 m/s . The pipe narrows to one-half its
original diameter.
The speed of the water is 8 m/s
what is the pressure of the water?
Water is flowing at the rate of 1.676 m/s in a 3.068 inches’ diameter horizontal pipe...
Water is flowing at the rate of 1.676 m/s in a 3.068 inches’
diameter horizontal pipe at a pressure p1 of 68.9 kPa. It then
passes to a pipe having an inside diameter of 2.067 inch. The
density of the water is 998 kg/m3 . a) Calculate the new pressure
p2 in the 2.067inch pipe. Assume no friction losses b) If
the piping is vertical and the flow is upward, calculate the new
pressure p2. The pressure tap for p2...
A fluid of viscosity 0,002 N-s /m2 and density 1000 kg/m3 flows with an average speed...
A fluid of viscosity 0,002 N-s /m2 and density 1000 kg/m3 flows
with an average speed of 1 m/s in a 2 cm-diameter horizontal smooth
pipe . Calculate
a)magnitude of shearing stress at the pipe wall.
b) shear stress velocity of flow
c) magnitude of pressure gradient to induce flow
Water, with a density of ?=1185 kg/m3 , flows in a horizontal pipe. In one segment...
Water, with a density of ?=1185 kg/m3 , flows in a horizontal
pipe. In one segment of the pipe, the flow speed is ?1=7.13 m/s .
In a second segment, the flow speed is ?2=1.57 m/s . What is the
difference between the pressure in the second segment ( ?2 ) and
the pressure in the first segment ( ?1 )?
P2-P1 =
A liquid of density 1110 kg/m3 flows steadily through a pipe of
varying diameter and height. At...
The mean velocity of water in a 150 mm horizontal pipe is 0.9 m/s. Calculate the...
The mean velocity of water in a 150 mm horizontal pipe is 0.9
m/s. Calculate the loss of head through an abrupt contraction to 50
mm diameter. If the pressure in the 150 mm pipe is 345 kPa, what is
the pressure in the 50 mm pipe, neglecting pipe friction?
In a horizontal pipe, water enters with a velocity of 2m / s when it is...
In a horizontal pipe, water enters with a velocity of 2m / s
when it is subjected to a pressure at the inlet of 200 Pw (water
pressure). Determine:
a) The speed of the water (in m / s) at the outlet if an outlet
pressure of 134 Pw is observed
b) If the area of the tube at the inlet is 0.75m2,
find the volumetric flow at the outlet.
(in m3 / sec)
A pump delivers water (r= 1000 kg/m3, µ= 0.860x10-3 kg/m·s) from one reservoir to another reservoir...
A pump delivers water (r= 1000 kg/m3, µ= 0.860x10-3 kg/m·s) from
one reservoir to another reservoir through 120 m of 0.05 m diameter
pipe. Volumetric flow rate in the pipe line is measured with
venturi meter. Throat diameter of venturi meter is 38 mm and
pressure drop in the venturi meter is 156.9 kPa.The surface of the
pipe is rough e/D=0.0001. Calculate the power of the pump required
for the water–transfer. See the figure below for several pipe–
fittings installed...
0.80 m3/s of water flows in a horizontal smooth rectangular duct of height 0.50 m. The...
0.80 m3/s of water flows in a horizontal smooth
rectangular duct of height 0.50 m. The ratio of width to height is
1:2. The whole cross-section remains wet when the water is flowing
inside the duct. Calculate the head loss in meter (with
2 decimal places) in 30 m of this duct. (T =
20 °C; friction factor: f = 0.316Re-0.25)
The flowrate of water at 20 deg C is 0.01 m3/s in a pipe with a...
The flowrate of water at 20 deg C is 0.01 m3/s in a pipe with a
diameter of 10 cm. Is the flow:
Laminar
Transitional
Turbulent
Can't tell
When the specific humidity of air increases the the air is said
to be
Cooled
Humidified
Dehumidified
Heated
What is the relative humidity for saturated air?
Cannot be determined
0%
50%
100%
ADVERTISEMENT
Need Online Homework Help?
Get Answers For Free
Most questions answered within 1 hours.
ADVERTISEMENT
Active Questions
asked 5 minutes ago
asked 18 minutes ago
asked 20 minutes ago
asked 24 minutes ago
asked 29 minutes ago
asked 38 minutes ago
asked 44 minutes ago
asked 49 minutes ago
asked 50 minutes ago
asked 56 minutes ago
asked 1 hour ago
asked 1 hour ago