Question

Suppose the adiabatic compressor takes in nitrogen gas at 30 C and 1 atm and compresses...

Suppose the adiabatic compressor takes in nitrogen gas at 30 C and 1 atm and compresses it to 275 C and 5 atm. a) Find the compressor efficiency, nc. b) What is the specific entropy generation, Sgen? c) Assuming the mass flow rate 0.40925 kg/s, how much power would the compressor require?(d)Draw the P-v, T-v, and T-s diagrams for the compressor. Clearly label each point

Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
An adiabatic air compressor compresses 0.1 kg/s of air at 120 kPa and 22 C to...
An adiabatic air compressor compresses 0.1 kg/s of air at 120 kPa and 22 C to 900 kPa and 227 C. Determine the power required to do the job. Express the power in kW and enter the absolute value (no signs).
An adiabatic air compressor compresses 10.6 L/s of air at 120 kPa and 20°C to 1000...
An adiabatic air compressor compresses 10.6 L/s of air at 120 kPa and 20°C to 1000 kPa and 300°C. The constant pressure specific heat of air at the average temperature of 160°C = 433 K is cP = 1.018 kJ/kg·K. The gas constant of air is R = 0.287 kPa·m3/kg·K. Determine the work required by the compressor
nitrogen gas enters an adiabatic steady flow device at 0.20 MPa, 120 C with a velocity...
nitrogen gas enters an adiabatic steady flow device at 0.20 MPa, 120 C with a velocity of 16.57 m/s. At the exit, conditions are 2.40 MPa and 520 C. This device is a compressor or a turbine and kinetic and potential energies may be neglected. the inlet is a circular duct with a diameter of 12.00 cm. For nitrogen M=28. Find other properties in Table A-20. R = 8.314 1. Find the mass flow rate of the gas (kg/s) 2....
Steam enters an adiabatic compressor at 100 kPa and 125°C, ejecting at 1000 kPa and 565°C....
Steam enters an adiabatic compressor at 100 kPa and 125°C, ejecting at 1000 kPa and 565°C. What is the fractional isentropic efficiency of this compressor? (if your answer is 23%, enter the value 0.23) Draw and label 2 diagrams: your real compressor and your "fake" compressor, and remember that the two share in common identical feed streams but only the pressure in the exiting stream.
An adiabatic gas turbine uses air to produce work. Air expands adiabatically from 600 kPa and...
An adiabatic gas turbine uses air to produce work. Air expands adiabatically from 600 kPa and 287 C to 90 kPa and 67 C. Take specific heats at room temperature (300 K). a) Find the isentropic efficiency of the turbine. b) Find the work produced by the turbine for a mass flow rate of 2.5 kg/s. c) If the mass flow rate of air is again 2.5 kg/s, find the entropy generation under steady conditions.
NO INTERPOLATION REQUIRED Air enters an adiabatic turbine at 1000 kPa and 1625 degrees C (state...
NO INTERPOLATION REQUIRED Air enters an adiabatic turbine at 1000 kPa and 1625 degrees C (state 1) with a mass flow rate of 5 kg/s and leaves at 100 kPa the isentropic efficiency of the turbine is 85%. Neglecting the kinetic energy change of the steam, and considering variable specific heats, determine: a. the isentropic power of the turbine Isentropic power in kW b. the temperature at the turbine exit temperature at exit in degrees C c. the actual power...
3. Air with 100 kPa, 300 K flows into the insulating compressor with a flow rate...
3. Air with 100 kPa, 300 K flows into the insulating compressor with a flow rate of 2 kg/s, compressed to 1000 kPa and then discharged to the exit. The back entropy efficiency of the compressor is 82%. The gas constant of the ideal gas is the air, and the meanness of the air is , The mean ratio is k=1.4. Ignore kinetic energy and position energy. 1) Draw a schematic diagram and a T-s plot of the compressor. 2)...
Air enters the compressor of an ideal gas refrigeration cycle at 7oC and 40 kPa and...
Air enters the compressor of an ideal gas refrigeration cycle at 7oC and 40 kPa and the turbine at 37oC and 170 kPa. The mass flow rate of air through the cycle is 0.3 kg/sec. Assuming variable specific heats for air, determine (a) the rate of refrigeration, (b) the net power input, and (c) the coefficient of performance. Also, draw the T-s diagram of the gas refrigeration cycle.   
1- A certain amount of O2, as an ideal gas, is contained in a cylinder-piston system...
1- A certain amount of O2, as an ideal gas, is contained in a cylinder-piston system and develops a process from T1 = 300 K, P1 = 200 kPa to T2 = 1500 K and P2 = 150 kPa. Determine the specific entropy change in kJ / (kg K). 2- A certain amount of H2O in a closed rigid cylinder is cooled from T1 = 800 ° F and P1 = 100 lbf / in2 to P2 = 20 lbf...
Ammonia is brought from saturated vapor at 300 kPa to 1400 kPa, 140oC in a steady...
Ammonia is brought from saturated vapor at 300 kPa to 1400 kPa, 140oC in a steady flow adiabatic compressor. Thermodynamic properties of ammonia at initial and final states are given as : h1= hi = 1431.7 kJ/kg, s1 = s­i = 5.4565 kJ/kg-K h2= he = 1752.8 kJ/kg, s2= se = 5.7023 kJ/kg-K          h2,s = he,s = 1656.08 kJ/kg a) Find the actual specific work input to the compressor. b) Calculate the specific work input to the compressor for isentropic...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT