Question

Explain the behavior of convection coefficient for external flow over a flat plate. Show it in...

Explain the behavior of convection coefficient for external flow over a flat plate. Show it in a plot as well.

Homework Answers

Answer #1

Solution:-

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A flat plate is oriented at an angle of attack of 900 to the flow in...
A flat plate is oriented at an angle of attack of 900 to the flow in a low-speed wind tunnel. Assume the pressure over the front of the plate is constant and equal to the stagnation pressure. Assume the pressure on the reward facing side is also constant but equal to the free stream static pressure. Since the flat plate is perpendicular to the flow, the resulting drag is primarily pressure drag as opposed to skin friction drag. Show that...
Air at 20°C blows over a hot plate 50 by 75cm maintained at 250°C.The convection transfer...
Air at 20°C blows over a hot plate 50 by 75cm maintained at 250°C.The convection transfer coefficient,h, is 25W/Km2 .Assuming the plate is made of carbon steel (1%) 2cm thick and that 300W is lost from the plate surface by radiation, calculate the inside plate temperature?
. Air flows with Mach 2.8 over a flat plate that is set at an angle...
. Air flows with Mach 2.8 over a flat plate that is set at an angle of 7° to the upstream flow. The pressure in the upstream flow is 100 kPa. Find the lift and drag coefficients using linearized theory.
Liquid water at velocity of 2 m/s and temperature of 15 °C flows over a flat...
Liquid water at velocity of 2 m/s and temperature of 15 °C flows over a flat plate. The plate has a width of 1 m, length of 0.4 m and surface temperature of 37 °C. Determine: (a) the average heat transfer coefficient. (b) the convection heat transfer rate from the top surfacc of the platc.
Found the boundary layer flow on the flow through the flat plate in the water tunnel....
Found the boundary layer flow on the flow through the flat plate in the water tunnel. The length of the plate is, L = 30 cm and width b = 1 m. Meanwhile freestream speed is, U = 2 m / s with the speed profile is parabolic and. Draw, and the x / L, by formulating it ! Please answer this question
A flat plate measuring 20 cm by 20 cmis exposed to the flow of 30 degree...
A flat plate measuring 20 cm by 20 cmis exposed to the flow of 30 degree C water at a velocity of 35 cm/s. If the plate is maintained at a uniform temperature of 95 degree C, what is the total convective heat transfer from the plate?
Problem 4: Air at 20°C and 1 atm flows over a horizontal flat plate at 1...
Problem 4: Air at 20°C and 1 atm flows over a horizontal flat plate at 1 m/s. The plate is 20m by 1m and is maintained at 60°C. If the flow is in the direction of smaller side, calculate the power needed to maintain the surface temperature. Also repeat problem 4 for a case where air velocity is zero.
Determine the hydrodynamic and thermal entry lengths as well as the convection heat transfer coefficient for...
Determine the hydrodynamic and thermal entry lengths as well as the convection heat transfer coefficient for the flow of (a) air and (b) water at a velocity of 2 m/s in an 8 cm diameter and 7 m long tube when the tube is subjected to a uniform heat flux from all surfaces. Use fluid properties at 300 K.
Liquid (A) flows down as a thin film over the outside surface of a vertical flat...
Liquid (A) flows down as a thin film over the outside surface of a vertical flat plate 1.5 m wide (W = 1.5 m) and 3.5 m long (L = 3.5). Inert gas (B) flows across (perpendicular to) the width of the flat plate at a speed of 5 m/s. The supply of (A) is 0.27 mol/s at one end of the plate and the flow is considered to be turbulent. The gas composition of (A) at the edge of...
Explain the mass transfer in the laminar boundary layer when the fluid is in laminar flow...
Explain the mass transfer in the laminar boundary layer when the fluid is in laminar flow over a flat plate.