Question

Make a graph of the solidification time for a cylindrical casting with a volume of Vc=20,000...

Make a graph of the solidification time for a cylindrical casting with a volume of Vc=20,000 mm^3 as a function of the diameter to length ratio. Assume that the solidification time is five minutes for a sphere of volume Vs =10,000mm^3

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Question: Total time for solidification of a cubic casting of dimensions 5.0 cm × 5.0 cm...
Question: Total time for solidification of a cubic casting of dimensions 5.0 cm × 5.0 cm × 5.0 cm × is 1.6 min. A cylindrical riser with diameter to height ratio 0.5 is required so that the time for solidification of the riser is 3.2 min. Applying Chvorinov’s rule, the height of the riser (in cm) is? Provide proper answer
Quenching of a Steel Billet. A cylindrical steel billet 1 ft in diameter and 3 ft...
Quenching of a Steel Billet. A cylindrical steel billet 1 ft in diameter and 3 ft long, initiallyat 1000°F is quenched in oil. Assume that the surface of the billet is at 200°F through out the quenching. The steel has the following properties, assumed to be independent of temperature:k = 25 Btu/(hr×ft×°F), r= 7.7 g/cm3, CP= 0.12 cal/g×°C Estimate the temperature of the hottest point in the billet after five minutes of quenching.Neglect end effects, that is , make the...
Familiarize yourself with the subplot and hold command. Using the subplot and plot commands, plot the...
Familiarize yourself with the subplot and hold command. Using the subplot and plot commands, plot the volume of a sphere as a function of it’s radius for values of radius from 1 to 10. On the same graph plot the surface area of a sphere as a function of the radius ( from radius = 1 to 10). Use different colors for the two plots ( help plot will give details on how to select colors). Use the following formulas:...
A cylindrical capacitor of length 1 cm, inner radius 0.010 cm, and outer radius 0.015 cm...
A cylindrical capacitor of length 1 cm, inner radius 0.010 cm, and outer radius 0.015 cm is filled with water, which has dielectric constant K = 80.10 at 20◦C. Assume the capacitor has been connected to an ideal 6V battery for a long enough time for the system to have reached equilibrium. a). Find the surface charge densities in the water on both the inner and outer surface. What is the field ~ D as a function of r inside...
Darcy's law gives us the volume flow rate-volume per time (for example, cubic meters per day,...
Darcy's law gives us the volume flow rate-volume per time (for example, cubic meters per day, m^3/day). Another way to express volume is on a per-unit-area basis. For example, if we have a 1-m^3 cube, we know its base is 1 m^2 the cross-sectional area of the cube-and its height is 1m. If we fill the cube with water, we can say we have 1m of water per unit area. Darcy's law can be rearranged to calculate the volume flow...
A steel sphere has an inner volume of 4 liters and weighs 15 lbs when empty....
A steel sphere has an inner volume of 4 liters and weighs 15 lbs when empty. it also has a hole in the top that is 3.33 mm in diameter. the sphere is half filled with ice and the other half is filled with air. the whole system starts at STP. (you do not need the specific heat of air ) 1. what is the total energy needed to raise this system to 100 degrees C? A 999 W heater...
1. Physical units in mechanics are usually some combination of the dimensions time T, mass M,...
1. Physical units in mechanics are usually some combination of the dimensions time T, mass M, and length L. Consider the physical quantities ?, ?, ?, ?, and ? with dimensions [?]=M, [?]=L, [?]=LT^−1, [?]=LT^−2, and [?]=T. Enter the dimensional expression of the quantity on the right-hand side of each equation. Your answers may contain only M, L, T, and exponents. Assume that each of the following equations is dimensionally consistent. (a) K=1/2mv^2 [K] = (b) p=mv [p]= (c) k=-ma/r...
Part I The elementary gas phase reaction (CH3)3COOC(CH3)3 --> C2H6 + 2CH3COCH3 is carried out isothermally...
Part I The elementary gas phase reaction (CH3)3COOC(CH3)3 --> C2H6 + 2CH3COCH3 is carried out isothermally in a flow reactor. The reaction rate constant at 500C is 1x10-4 min-1 and the activation energy is 85 kJ/mol. Pure di-tert-butyl peroxide enters the reactor at 10 atm and 127oC and a molar flowrate of 2.5 mol/min. Calculate the reactor volume and space time to achieve 90% conversion in; a) PF reactor b) CSTR reactor c) Propose the diameter (Dt) and length (L)...
Criteria for Success: To be successful you will make sure you complete diagrams as instructed in...
Criteria for Success: To be successful you will make sure you complete diagrams as instructed in the tasks, including proper values on the x & y-axis as well as labeling those. You also need to make sure to list or provide explanation where necessary or where it is asked in the tasks. A successful submission would be very clear and easy to read and it would be easy to see the differences in pressures and volumes based on the given...
Imagine that you have two cups, one containing 1540 g of water and the other one...
Imagine that you have two cups, one containing 1540 g of water and the other one containing some amount of an unknown liquid. The specific heat of water is 4.19 J/g·°C, and the specific heat of the unknown liquid is 7.03 J/g·°C. You use two identical immersion heaters to heat the water and the unknown liquid simultaneously. Assume that all the heat from the heater is used to heat the content of the cups. (a) You started heating the water...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT