Question

a solid circular steel rod has a length of 70 mm, diameter of 20 mm, and...

a solid circular steel rod has a length of 70 mm, diameter of 20 mm, and an eccentricity(offset) of 6 mm.Syiely =300Mpa. find the critical buckling load if its boundary condition are fixed-free(use theoretical value in table)

Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A steel rod without constrain has a length of 200 mm and diameter of 20 mm...
A steel rod without constrain has a length of 200 mm and diameter of 20 mm at a temperature of 25oC. If the rod is heated uniformly to 125oC, what will be the length and diameter (accurate to 1/100 mm). What will be the stress at 125oC? The linear coefficient of thermal expansion of steel is 12.5x10-6 m/m/C.
A solid steel bar 100 mm diameter is firmly encased by an 8 mm brass liner...
A solid steel bar 100 mm diameter is firmly encased by an 8 mm brass liner over its entire 750 mm length. The component is securely fixed at both ends and the temperature of the system is evenly increased by 100ºC. Calculate EACH of the following: The difference between the induced stresses; The final length of the bar if it is free to expand. Note:   Modulus of elasticity for steel = 206 GN/m2             Modulus of elasticity for brass =...
Q3: Tension test was conducted on a mild steel rod having diameter 1.5 cm and length...
Q3: Tension test was conducted on a mild steel rod having diameter 1.5 cm and length 20 cm. While applying a load of 10 kN, there will be an extension of 0.012 cm on a length of 20 cm. Maximum load carried by the rod was found to be 26 kN and the load beyond which stress is not proportional to strain was observed to be 11 kN. When the specimen breaks, the extension of the rod for 20 cm...
A solid steel shaft, 20 mm in diameter and 1 m long, is placed concentrically inside...
A solid steel shaft, 20 mm in diameter and 1 m long, is placed concentrically inside a hollow duralumin shaft with inside and outside diameters of 30 mm and 33 mm respectively and a length of 500 mm. The ends of the hollow shaft are rigidly fixed to the solid shaft. Determine (a) the torsional stiffness of the composite shaft (b) the maximum torque to which the composite shaft may be subjected if the allowable shear stresses for steel and...
A straight rod of solid polymer is of length 1 m and diameter 10 mm. The...
A straight rod of solid polymer is of length 1 m and diameter 10 mm. The polymer is linearly viscoelastic with a tensile creep compliance given by: D = 2- exp(-0.1t); Gpa^-1 Where t is in hours. The rod is suspended vertically and a mass of 10 kg is hung from it for 10 hours. Identify the time domain of this property test procedure.
A rod has a square cross section of (5 x 5) mm. length of the rod...
A rod has a square cross section of (5 x 5) mm. length of the rod is 120 cm. The allowable stress is 400 MPa. After applying the load (F), square section changes to (4.95 x 4.95) mm. 1. What is the type of the load (F), is it tension or compression? 2. What is the longitudinal strain in steel rod? 3. What is the modulus of elasticity of the material of the rod? 4. What is the value of...
Due to the operational conditions and temperature gradient, a 70 mm diameter, 1.55 m long steel...
Due to the operational conditions and temperature gradient, a 70 mm diameter, 1.55 m long steel rod within a machine assembly is subjected to a combination of tensile loading of 150 N and thermal loading which imposes a longitudinal force of 230 N. The total loading results in an even distribution of forces on the body of the rod causing it to change its dimensions by increasing 0.5 mm in length at both ends and decreasing by 0.0125 mm at...
A cylindrical specimen of stainless steel having diameter of 12.8 mm and a guage length of...
A cylindrical specimen of stainless steel having diameter of 12.8 mm and a guage length of 50.88 mm(2.000in.) is pulled in tension. Use the load-elongation characterisitcs shown in the following table. Plot the data as engineering stress vs. engineering strain. Then compute the modulus of elasticity, yeild strength at a strain offset of 0.002, determine the tensile strength of this alloy, approximate ductility in percent elongation and the modulus of resilience. N mm 0 50.8 12700 50.825 25400 50.851 38100...
A rod of brass originally 600 mm long is pulled in tension along its longitudinal axis...
A rod of brass originally 600 mm long is pulled in tension along its longitudinal axis with a stress of 45 MPa. What will be the length of the rod when the stress is applied? A rod of Titanium with a diameter of 6 mm and a length of 300 mm is subjected to an elastic force of 5000 N. a) Estimate the diameter of the rod when the load has been applied. b) What is the diameter of the...
Consider the 1040 carbon steel listed in Table 6.1. (a) A 20-mm-diameter bar of this alloy...
Consider the 1040 carbon steel listed in Table 6.1. (a) A 20-mm-diameter bar of this alloy is used as a structural member in an engineering design. The unstressed length of the bar is precisely 1 m. The structural load on the bar is 1 .2 x 10^5 N in tension. What will be the length of the bar under this structural load? (b) A design engineer is considering a structural change that will increase the tensile load on this member....
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT