Question

Select right answer. A rotating steel flat disk has 200 mm inner diameter and 300 mm...

Select right answer. A rotating steel flat disk has 200 mm inner diameter and 300 mm outer diameter. If the maximum shear stress is to not exceed 200 MPa the allowable speed in rpm is around

Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load of 325 kN. If the compressive stress is 150 MPa, lateral strain for external diameter is is 0.000325 and Poisson’s ratio is 0.3, find the minimum wall thickness required for the column. Also calculate the shear modulus for the material of the column. Take E = 210 GPa.   
A cylindrical tank is made of A36 steel and has an inner diameter of 1.5 meters....
A cylindrical tank is made of A36 steel and has an inner diameter of 1.5 meters. Using Maximum Shear Stress Theory and a Factor of Safety of 2 with respect to the yield, determine the minimum wall thickness (mm) required:
WITH COMPLETE SOLUTION A welded steel girder having the cross section of two fabricated 280 mm...
WITH COMPLETE SOLUTION A welded steel girder having the cross section of two fabricated 280 mm x 25 mm flange and a 600 mm x 15 mm web plate. The plates are joined by four fillet welds that run continuously for the length of the 6 m span girder. Each weld has an allowable load of 330 kN/m. 1.Determine the maximum allowable shear force V for the girder in kN. 2. Calculate the maximum bending stress of the girder if...
A solid alloy shaft of 50 mm diameter is coupled in series with a hollow steel...
A solid alloy shaft of 50 mm diameter is coupled in series with a hollow steel shaft of same external diameter. Determine the internal diameter of the hollow steel shaft if the angle of twist per unit length in hollow shaft is 75% of that of the solid alloy shaft. Also, determine the speed at which the compound shaft must be driven to transmit 200 kW, if the limiting shear stresses are 55 MPa and 75 MPa in alloy and...
A steel rod without constrain has a length of 200 mm and diameter of 20 mm...
A steel rod without constrain has a length of 200 mm and diameter of 20 mm at a temperature of 25oC. If the rod is heated uniformly to 125oC, what will be the length and diameter (accurate to 1/100 mm). What will be the stress at 125oC? The linear coefficient of thermal expansion of steel is 12.5x10-6 m/m/C.
A solid steel shaft, 20 mm in diameter and 1 m long, is placed concentrically inside...
A solid steel shaft, 20 mm in diameter and 1 m long, is placed concentrically inside a hollow duralumin shaft with inside and outside diameters of 30 mm and 33 mm respectively and a length of 500 mm. The ends of the hollow shaft are rigidly fixed to the solid shaft. Determine (a) the torsional stiffness of the composite shaft (b) the maximum torque to which the composite shaft may be subjected if the allowable shear stresses for steel and...
10. A cast iron wheel of mean diameter 3 metre has six arms of elliptical section....
10. A cast iron wheel of mean diameter 3 metre has six arms of elliptical section. The energy to be stored in it is 560 kN-m when rotating at 120 r.p.m. The speed of the mean diameter is 18 m/s. Calculate the following: (a)Assuming that the whole energy is stored in the rim, find the cross-section, if the width is 300 mm. (b)Find the cross-section of the arms near the boss on the assumption that their resistance to bending is...
A steel piano wire (Y = 200 GPa) has a diameter of 0.780 mm. At one...
A steel piano wire (Y = 200 GPa) has a diameter of 0.780 mm. At one end it is wrapped around a tuning pin of diameter 8.00 mm. The length of the wire (not including the wire wrapped around the tuning pin) is 66.0 cm. Initially, the tension in the wire is 379 N. To tune the wire, the tension must be increased to 407 N. Through what angle must the tuning pin be turned? (θ = answer°)
Consider an aluminum annular disk with an outer radius 63.2 mm and inner radius 7.9 mm....
Consider an aluminum annular disk with an outer radius 63.2 mm and inner radius 7.9 mm. The mass of the disk is 464 grams. The disk is allowed to rotate on a frictionless table with the rotation axis at its center. The disk has a small pulley rigidly mounted at the top concentrically. The pulley's radius is 12.1 mm, and the mass of the pulley is negligible. A string is wrapped around the pulley, and a hanging mass of 19.3...
A steel piano wire (Y = 200 GPa) has a diameter of 0.790 mm. At one...
A steel piano wire (Y = 200 GPa) has a diameter of 0.790 mm. At one end it is wrapped around a tuning pin of diameter 8.00 mm. The length of the wire (not including the wire wrapped around the tuning pin) is 66.0 cm. Initially, the tension in the wire is 381 N. To tune the wire, the tension must be increased to 413 N. Through what angle must the tuning pin be turned?
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT