Question

mechanical component is 200 mm wide, and 10 mm thick, made of aluminum and yields a...

mechanical component is 200 mm wide, and 10 mm thick, made of aluminum and yields a stress of 240 Mpa. calculate the max safe load P if the normal stress cannot exceed yield stress. Factor of safety is 3.

Engineering   Mechanical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A leaf spring is to be made of seven steel plates 65 mm wide and 6.5...
A leaf spring is to be made of seven steel plates 65 mm wide and 6.5 mm thick. Calculate the length of the spring, so that it may carry a central load of 2.75 kN, the bending stress being limited to 160 MPa. Also calculate the deflection at the centre of the spring. Take E for the spring material as 200 GPa
A normal mild steel specimen having 50 mm 2 cross section area and 10 cm long...
A normal mild steel specimen having 50 mm 2 cross section area and 10 cm long gauge length was tested. 1. Draw the stress- strain diagram 2. calculate the final length of the bar compare when the specimen unloaded from 400 MPa? 3. calculate the elastic and plastic deformation when the specimen unloaded from 400 MPa Proportionality limit Ultimate Load Failure Load Stress (MPa) 320////// 500 /////////400 Strain 0.0018 //// 0.06///////// 0.12
1. An aircraft weights 120,000 lbs., it has 35,000 lbs. of fuel added. What will be...
1. An aircraft weights 120,000 lbs., it has 35,000 lbs. of fuel added. What will be its takeoff weight? If there is 350 lbs. of excess weight what will be its new weight? Hint 1 kg = 2.21 lbs. Gravity = 9.81 N/m (up to 5 points) 2. Why is the fracture value less than the UTS value shown on a stress-strain graph? (up to 5 points) 3. Use the table below that gives the yield point for three materials....
The 7-mm-thick base plate of an iron is made of an aluminum alloy (? = 2,700...
The 7-mm-thick base plate of an iron is made of an aluminum alloy (? = 2,700 kgm-3; c = 950 Jkg-1K-1; k = 200 Wm-1K-1; ? = 0.8), and has outer surface area of 0.04 m2, perimeter of 0.7 m, and maximum length of 0.3 m. An electrical resistance heater applies a uniform heat flux of 12.5 kWm-2 to the inner surface of the base plate when the iron is turned on. The outer surface of the base plate is...
1. An oven chimney is made of brick with a heat transmission coefficient 1.1 W/mK 10...
1. An oven chimney is made of brick with a heat transmission coefficient 1.1 W/mK 10 cm thick. Since the shaft exterior radiation beam coefficient is 0.8 and the flue gas temperature is 350°C, the external ambient temperature is 25°C and the outer ambient heat transport coefficient is 20 W/m2K; a) Calculate the shaft exterior temperature. b) In order to reduce the risk of burn injury that may occur in the body, the shaft is asked to be below 55°Cve...
1. What is an ISP (Integrated Service Provider) for supply chains? (1 point) A. A consultant...
1. What is an ISP (Integrated Service Provider) for supply chains? (1 point) A. A consultant agency which integrates the supply chain for companies B. A 2 PL or a 3PL, but not a 4PL C. A company supplying transportation and warehousing services D. A logistics service company specialized in suppling VAS (value added services) 2. What characterizes a 4 PL? (1 point) A. They are non-asset based and provides integrated services primarily supplied by asset based providers, for example...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT