Question

Calculate the shearing force (kN) required for blanking a circular part with a diameter of 55mm...

Calculate the shearing force (kN) required for blanking a circular part with a diameter of 55mm from and metallic sheet that is 2.1mm thick and has a tensile strength of 809MPa

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m...
2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. Assuming no permanent deformation occurred in that material, what is the modulus of elasticity?
A cable with a diameter of 6 mm is subject to a maximum tensile force of...
A cable with a diameter of 6 mm is subject to a maximum tensile force of 9 kN. The cable must not extend by more than 0.5% and must not yield. Properties of four materials (W, X, Y and Z) are listed in the table below. Which of materials in the table above are suitable for the cable? Material Yield strength (MPa) Tensile strength (MPa) Young’s Modulus (GPa) W 200 450 195 X 320 400 45 Y 640 700 85...
A hollow right circular cylinder is made of cast iron and has an outside diameter of...
A hollow right circular cylinder is made of cast iron and has an outside diameter of 75 mm and an inside diameter of 60 mm. If the cylinder is loaded by an axial compressive force of 50 KN, determine the total shortening (in mm) in a 600-mm length. Take the modulus of elasticity to be 100 GPa and neglect any possibility of lateral buckling of the cylinder. show the solution
Hot forging is used to reduce a metallic cylindrical workpiece with a diameter of 12 cm...
Hot forging is used to reduce a metallic cylindrical workpiece with a diameter of 12 cm and height of 25 cm to a height of 12 cm. Barreling of the workpiece is eminent knowing that the coefficient of friction of the open die plate with the workpiece is 0.3. The process takes 8 seconds to complete at a constant forging speed. The strength coefficient of the workpiece C= 200 MPa and strain rate sensitivity exponent m = 0.32. Calculate the...
1.A hydraulic lift is lifting a car that weighs 14 kN. The area of the piston...
1.A hydraulic lift is lifting a car that weighs 14 kN. The area of the piston supporting the car is A, the area of the other piston is a, and the ratio A/a is 101.7. How far must the small piston be pushed down to raise the car a distance of 1.2 cm 2.The pressure inside a bottle of champagne is 4.8 atm higher than the air pressure outside. The neck of the bottle has an inner radius of 0.9...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load...
A hollow circular steel column 2m long and outer diameter 200 mm carries an axial load of 325 kN. If the compressive stress is 150 MPa, lateral strain for external diameter is is 0.000325 and Poisson’s ratio is 0.3, find the minimum wall thickness required for the column. Also calculate the shear modulus for the material of the column. Take E = 210 GPa.   
A metallic bar is to be cold withdrawn from 8mm diameter to 6 mm through a...
A metallic bar is to be cold withdrawn from 8mm diameter to 6 mm through a die with an angle, half-angle, of 15° and with coefficient of friction of 0.12. The strength coefficient for the bar K= 300 MPa and its strain hardening exponent n = 0.35. calculate: Area reduction. The inhomogeneous deformation factor, F. The drawing force (N). Is the reduction possible?
Determine the depth at which a circular footing of (2+0.4Y) m diameter be founded to provide...
Determine the depth at which a circular footing of (2+0.4Y) m diameter be founded to provide a factor of safety of 3, if it has to carry a safe load of (1500+10Y) kN. The foundation soil has a cohesion of 10kN/m2, an angle of internal resistance of (30 +Y)o. The water table is at the ground surface and the unit weight of the soil is 19 kN/m3. Use Terzaghi’s Analysis. y=2
For an object in uniform circular motion, a centripetal force (acceleration) is required. a) True b)...
For an object in uniform circular motion, a centripetal force (acceleration) is required. a) True b) False
A (65 KN) wheel load is placed on a Portland cement concrete slab that is (0.240...
A (65 KN) wheel load is placed on a Portland cement concrete slab that is (0.240 m) thick. The concrete has a modulus of elasticity of (27 GPa). The modulus of subgrade reaction is (0.3 N/mm3). Calculate Poisson ratio, if the edge stress is (1.715 MPa) due to a wheel load applied on an equivalent circular area whose radius is (16 cm) for above mentioned slab.