Question

circuit output equations are F1 = ∑ (1,3,5,7,9,15), F2 = ∑ (0,2,4,6,8,10,14), design the circuit on...

circuit output equations are F1 = ∑ (1,3,5,7,9,15), F2 = ∑ (0,2,4,6,8,10,14), design the circuit on Multisim using 8x1 MUX and 16x1 MUX. The circuit with probes on output. Attach a screenshot of Multisim circuit, and attach the first page of the data sheet of the chose ICs.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design an op-amp circuit that will provide an output voltage equal to the average of three...
Design an op-amp circuit that will provide an output voltage equal to the average of three input voltages. You may assume that the input voltages will be confined to the range -10V ?Vin ?10V. Verify your design by using Multisim software and a suitable set of input voltages.
Using a decoder and external gates, design the combinational circuit defined by the following Boolean functions:...
Using a decoder and external gates, design the combinational circuit defined by the following Boolean functions: ( ‘ means “bar”). F1 = x’y’z’ + xz F2 = xy’z’ + x’y F3 = x’y’x + xy
1. Design a circuit with input: AC (10Vp Sin wave 50Hz), and output signal with +8.7V...
1. Design a circuit with input: AC (10Vp Sin wave 50Hz), and output signal with +8.7V and -14.7V. (Hint: Use Diodes) 2. Design an inverter circuit using PMOS. Also show the output waveform. Design on proteus.
Design an even parity detection circuit. A parity bit is an error checking mechanism. Your circuit...
Design an even parity detection circuit. A parity bit is an error checking mechanism. Your circuit will count the number of 1’s in a stream of bits. If the number of 1’s is even, the circuit turns on an output called Y. Assume a single bit at each cycle – call the input X. Do not use an accumulator or counter. Design the even parity detection circuit using J-K flip-flops. Your answer must include: a. The state diagram. b. The...
4. Using an op amp, design a circuit to produce an output voltage related to two...
4. Using an op amp, design a circuit to produce an output voltage related to two input voltages by the equation ?? = 1 2 ?2 − ?? (Use the feedback resistance R2 = 10kΩ). Devise a procedure to verify your design.
Design a synchronous machine (Transition Table, K-maps, Final Equations, Circuit Diagram) that counts through the following...
Design a synchronous machine (Transition Table, K-maps, Final Equations, Circuit Diagram) that counts through the following sequence in the order shown below. Note, there are no inputs or output variables, so your Q values must reflect the Hex value listed. A 4 1 2 6 3 9 C 7 and repeat a) using D flip-flops and combinational logic b) using a PROM device (must show Hex values in order) and 4-bit D-Register
Using one SR one JK and one D flip flop design a sequential circuit that generates...
Using one SR one JK and one D flip flop design a sequential circuit that generates the output pattern: 7-6-5-4-3-2-1-0 and then the sequence repeats. Derive the equations for SA, RA, JB, KB, and DC.
Mealy state machines. (a) Design a Mealy state machine to detect the sequence 10010. There is...
Mealy state machines. (a) Design a Mealy state machine to detect the sequence 10010. There is a single input “x” and a single output “z”. The output is set to 1 when the sequence is detected. Design the state machine using gates and flip-flops in the standard way, i.e., begin with a state transition diagram and state transition table, do plain state assignment (e.g., for three state variables, first state is 000, next is 001, and so on), use K-maps...
Q.1.It is required to design an iterative combinational circuit that computes the equation Z=2*X-3, where X...
Q.1.It is required to design an iterative combinational circuit that computes the equation Z=2*X-3, where X is an n-bit signed number in 2’s complement representation. (Hint: -3 can be represented as -1+-1+-1 in 2’s complement representation, where -1 is represented as 111…..111). a)Determine the number of inputs and outputs needed for your 1-bit cell. Explain the meaning of values in the interface signals. b)Derive the truth table of your 1-bit cell. c) Derive minimized equations for your 1-bit using K-Map...
Design a 6-bit, shift-right register with D flip flops, and use it to implement a circuit...
Design a 6-bit, shift-right register with D flip flops, and use it to implement a circuit that detects the sequence “010010” (the rightmost bit is the first arriving). Information shifts one position right when a positiv edge of clk occurs The circuit has the following inputs and outputs (use exactly these names for inputs and outputs. Respect upper and lower case): clk: Input. Clock signal. RST: Reset signal. When RST = 1 flip flops are reset to 0. IN: Data...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT