Question

Can you make a common base bjt circuit in multisim with an oscilloscope? The oscilloscope should...

Can you make a common base bjt circuit in multisim with an oscilloscope? The oscilloscope should show that the voltage out is amplified and it's in phase with voltage in.
Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

Here is the circuit build-up in MULTISIM

Here green waveform is output signal and the red waveform is input signal. The amplitude of the output signal is more than the amplitude of input signal.

Please thumbs up

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
In MultiSim, design a PWM circuit. You will need a 0 to 9 counter, which you...
In MultiSim, design a PWM circuit. You will need a 0 to 9 counter, which you should build from flip flops and basic logic gates. The PWM input will come from 4 input switches as a binary number. For the comparator, you can build your own from basic gates, or use one of the commercially available comparator chips (74HC85 Digital IC). An oscilloscope in MultiSim can be used to verify duty cycles.
use multisim please Design:Create an RLC series circuit using the same source voltage (Vs) as input...
use multisim please Design:Create an RLC series circuit using the same source voltage (Vs) as input voltage equal to: vi(t) = 6 sin (400 pi * t) Select any R, L, and C you want as long as the measured (with the Watt meter) power factor is equal to 0.8(+/- 0.02). You can select any unique values of R, L, and C as long as you have at least 3 non-zero decimal places for each component. Show the Multisim schematic...
Hello, So, I was given a task to build a single stage BJT amplifier (Using NI...
Hello, So, I was given a task to build a single stage BJT amplifier (Using NI Multisim only), and it was specified to build it so it can gives you a voltage gain (Av) of 12, the circuit configuration is optional. Now, simulating the circuit is easy, but choosing the right components is what makes it complicated for me. Our instructor never talked about the designing process, or anything related to that. Is there any suggestions or guidance or even...
What happens when you increase the input voltage of a common emitter BJT amplifier?
What happens when you increase the input voltage of a common emitter BJT amplifier?
Can you design me a circuit with fixed collector-emitter voltage, the gain is not constant and...
Can you design me a circuit with fixed collector-emitter voltage, the gain is not constant and it varies depending on collector current. I want to generate the beta versus collector current graph with using BJT for a fixed collector-emitter voltage (5V). Collector should span the range (1mA--> 1000mA) or can you tell me how to vary the collector current and keep the collector-emitter voltage fixed? What are the key features to be careful about ? ? What type of components...
1. Create a voltage divider. Design a circuit which can provide a fraction of the voltage...
1. Create a voltage divider. Design a circuit which can provide a fraction of the voltage ( x V) out of the regular batteries. The equipment you can use: 2 D-batteries (about 1.5V each) and one piece of nichrome wire and some connecting wires. If you need to make 2V, how would you connect it? Draw a detailed circuit to show the connection. Explain in detail why it works. Use a voltmeter to check your design. Draw the voltmeter on...
Second order circuit as a band pass filter. 1. Consider a series RLC circuit of your...
Second order circuit as a band pass filter. 1. Consider a series RLC circuit of your choice with AC source. Find the resonance conditions (resonant frequency, quality factor cut-off frequencies and bandwidth. Simulate(multisim) the resonance condition by experimenting with AC signal of several different frequencies and comparing the output amplitudes. You need to show graphs of simulation with several different frequencies. Demonstrate that the simulation results confirm the calculated resonance effect. Make a band pass filter from circuit in (1)....
You examine a circuit containing a bipolar transistor. The base voltage is fixed, but the collector-emitter...
You examine a circuit containing a bipolar transistor. The base voltage is fixed, but the collector-emitter voltage is allowed to vary from an initial value of 1.1V to a final value of 3.8V . What must the Early voltage of the transistor be if the collector current doesn't change by more than 5%.
ANSWER ALL 4 QUESTIONS PLEASE 1-You have set up an LRC series circuit and are observing...
ANSWER ALL 4 QUESTIONS PLEASE 1-You have set up an LRC series circuit and are observing the voltage drop across the resistor on an ideal oscilloscope. If you disconnect the oscilloscope, does the current in the circuit change? Why or why not? 2-When a line light source with spectral lines is observed through a diffraction grating I. the blue lines are closer from the center than the red lines. II. the blue lines are farther from the center than the...
Make sketches of circuit diagrams showing how single, double and triple wattmeter methods can be used...
Make sketches of circuit diagrams showing how single, double and triple wattmeter methods can be used in the measurements of three phase power. Write down the expression for determining of the sum of readings from the all the wattmeters involved in each scenarios.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT