Question

Develop an expression for current in a controlled half-wave rectifier circuit that has a load consisting...

Develop an expression for current in a controlled half-wave rectifier circuit that has a load consisting of a series Resitor R and dc voltage VDC. The source is vs=Vm sin wt, and the delay angle is alpha. (a) Determine the average current if Vm=100 V,R=100 ohms, Vdc=24 V,w= 2p60 rad/s, and alpha= 75°.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A full-wave rectifier has a 120 V rms, 60 Hz ac source. The load is a...
A full-wave rectifier has a 120 V rms, 60 Hz ac source. The load is a series inductance, resistance and dc voltage source, with L = 100 mH, R = 10 Ω, and Vdc = 50 V. a). Determine an expression for load current. b). Determine the power absorbed by the dc voltage source. c). Determine the power absorbed by the resistance. d). Determine the power factor of the source.
Can a controlled half-wave rectifier with a series inductance, resistance and dc source in the load...
Can a controlled half-wave rectifier with a series inductance, resistance and dc source in the load side operate as an inverter (Power direction from DC source to AC source)? Why?
The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230...
The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230 Volt at 50 Hz. 24 Volt battery will be charged with 15A. An inductor, which is series connected to the battery, is used to limit the current ripple. Only The second harmonics of the output voltage is taken into account. The inductor R/L ratio is 50. The current ripple is allowed to be 4 amp peak to peak. Determine the firing angle and R...
Find the current in a circuit consisting of a coil and capacitor in series, if the...
Find the current in a circuit consisting of a coil and capacitor in series, if the applied voltage v= 120 volts, frequency f = 60 Hz; the inductance of the coil is L = 0.30 henry; the resistance of the coil is R = 40 ohms; and the capacitance of the capacitor is C= 2 µf. (b) Find the power used in the circuit.
Design a DC power supply that will deliver 100mA of current to a load with a...
Design a DC power supply that will deliver 100mA of current to a load with a ripple of 5%. Use a full wave rectifier and a 17 Peak Voltage Source with F= 60 Hz. Load resistance = 1k So Basically you just need to find the capacitance of the filtering capacitor. Please tell me how. This is what I did, but I think I'm wrong. The Vripple I got is (.05)*17 = .85 V. Then according to my manual, C...
A) What is the rms current in a series RC circuit if R = 3.4 kΩ...
A) What is the rms current in a series RC circuit if R = 3.4 kΩ , C = 0.87 μF , and the rms applied voltage is 100 V at 38 Hz ? Express your answer using two significant figures. Irms =   A   SubmitRequest Answer Part B What is the phase angle between voltage and current? Express your answer using two significant figures. ϕ =   ∘   SubmitRequest Answer Part C What is the power dissipated by the circuit? Express...
A series RLC circuit is driven by a voltage source which provides a time varying emf...
A series RLC circuit is driven by a voltage source which provides a time varying emf of ϵ = 100cos(8000t)V and consists of an resistor, capacitor and inductor with values of R = 100 Ohms, L = 1.00 mH, C = 1.00 µF a) What is the phase constant of the current? Enter your answer in radians. b) When the potential across the resistor is 0 V, what is the potential across the inductor? You might find a phasor diagram...
A 5-kW, 220-V shunt motor has an armature resistance of 0.15 ? and a field-circuit resistance...
A 5-kW, 220-V shunt motor has an armature resistance of 0.15 ? and a field-circuit resistance of 100 ?. The motor delivers rated output power at rated voltage when its armature current is 20 A. When the motor is operating at rated voltage, the speed is observed to be 1000 r/min when the machine is loaded such that the armature current is 15 A. In order to protect both the motor and the dc supply under starting conditions, an external...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT