Question

5-4 Design a class A power amplifier using an IRF530. Set Esupply = 18 Vdc, Rload...

5-4

Design a class A power amplifier using an IRF530. Set Esupply = 18 Vdc, Rload = 2 Ω, ein max = 5 Vp

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

We implement the class A power amplifier with N-mosfet amplifier.

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS) configuration with a...
Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS) configuration with a resistor in the Source. Its design should provide an amplification of -12V / V. The Voc voltage will be +8 VDC, the AC voltage will be 10 mV peak 5 kHz and the load resistance will be RL 2.2 kn.
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband...
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband voltage gain: Av = 100. – Lower 3-dB frequency: fc = 100 Hz. – Input Impedance: Zin ≥ 250 kΩ. – Output Impedance: Zo ≤ 100 Ω. – Power Supply: Vcc = 15 V. – The load resistance is 1 kΩ – Output capability with a 1–kHz sinusoidal test signal must be at least 2 V peak without severe distortion (i.e. clipping). – Transistor...
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS)...
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS) configuration with a resistor in the Source. Its design should provide an amplification of -12V / V. 2. The voltage Vcc will be +8 vDC, the AC voltage will be 10 mV peak 5 kHz and the load resistance will be RL 2.2 kn. 3. Simulate the circuit in LTSpice. It must choose resistors Ro, Rs, RG1 and RG2 such that the circuit operates...
Suppose that we design a noninverting amplifier using 5% tolerance resistors and an ideal op amp....
Suppose that we design a noninverting amplifier using 5% tolerance resistors and an ideal op amp. The nominal amplifier gain is +2. What are the minimum and maximum gains possible, assuming that the resistances are within the stated tolerance? What is the percentage tolerance of the gain?
Design a DC power supply that will deliver 100mA of current to a load with a...
Design a DC power supply that will deliver 100mA of current to a load with a ripple of 5%. Use a full wave rectifier and a 17 Peak Voltage Source with F= 60 Hz. Load resistance = 1k So Basically you just need to find the capacitance of the filtering capacitor. Please tell me how. This is what I did, but I think I'm wrong. The Vripple I got is (.05)*17 = .85 V. Then according to my manual, C...
Data set for ages of students in stats class: 17, 18, 18, 18, 18, 18, 18,...
Data set for ages of students in stats class: 17, 18, 18, 18, 18, 18, 18, 18, 18, 18, 18, 19, 19, 19, 19,19, 20, 20, 20, 21, 21, 21, 21, 21, 21, 22, 22, 22, 22, 23, 23, 23, 23, 24, 25, 25, 25, 26, 26, 27, 28, 28, 28, 28, 29, 29, 32, 36, 42 1) Compute the 5-number summary and create a modified box-plot, using the inner-quartile range to identify any outliers.
A company is required to design a DC power supply to power 3 different circuits. The...
A company is required to design a DC power supply to power 3 different circuits. The requirements for the circuits are as below: Circuit 1: Supply Voltage 5 Volt Circuit 2: Supply Voltage 9 Volt Circuit 3: Supply Voltage 3 Volt The parts available in that company are a 20V power supply unit and 4 Variable resistors (1 to 100Ω) for this design. You as a design engineer are required to help the company to design the power supply as...
Using MultisimBlue – Advanced Circuit Simulation Design Program make a I. CE Swamped Amplifier Circuit producing...
Using MultisimBlue – Advanced Circuit Simulation Design Program make a I. CE Swamped Amplifier Circuit producing the following: 1. DC Current Gain: ?DC = 150 (minimum value) 2. AC Voltage Gain: Av = 12 (minimum value) II. Required Components: 1. Transistor Q1 – 2N2222A producing a VCE between 8 V to 12 V 2. Input AC Source: 10 mVAC (14.14 mVpk) @ 1 kHz 3. Coupling and Bypass Capacitors – 30 µF (suitable for low frequencies) 4. Circuit VCC of...
Design a class with the following requirements: 1- give the class a name from your choice....
Design a class with the following requirements: 1- give the class a name from your choice. 2- write some code that creates three instance variables, choose a name and type for each one of them. (must have two private and one public variables) 3- Initialize the variables using two different constructors. 4- Use mutator and accessor methods (set and get) for the private data members. 5- Display the value of each member variable using a method. 6- In the main,...
Design a class with the following requirements: 1- give the class a name from your choice....
Design a class with the following requirements: 1- give the class a name from your choice. 2- write some code that creates three instance variables, choose a name and type for each one of them. (must have two private and one public variables) 3- Initialize the variables using two different constructors. 4- Use mutator and accessor methods (set and get) for the private data members. 5- Display the value of each member variable using a method. 6- In the main,...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT