Question

Example: The load with lagging 0.8 PF absorbs 60 watts of a 100 V, 60 Hz...

Example: The load with lagging 0.8 PF absorbs 60 watts of a 100 V, 60 Hz power line. Required to correct power factor to 0.9 lag. Find: 3- The original and last line current b) The value of the element to be added to achieve the required pf correction ...
power factor

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Three loads are connected in parallel across a 1500 Vrms - 60 hz. Load 1 absorbs...
Three loads are connected in parallel across a 1500 Vrms - 60 hz. Load 1 absorbs 23 kW and 14 kVAr capacitive. Load 2 absorbs 70 kVA with power factor 0.7 lagging. Load 3 absorbs 22kW with power factor = 1. Find: a) Complex impedance, seen from power source b) Power Factor of the setup and module of Rms current supplied by the source c) Complex impedance of Load 2 d) Value of capacitor to be connected to the combination...
Two parallel loads are connected to a 220-V, 60 Hz, single-phase source where the first load...
Two parallel loads are connected to a 220-V, 60 Hz, single-phase source where the first load consumes power 100kW at power factor 1 and the second load consumes 100kW at power factor 0.8 lagging. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.98 lagging. (a) Find the net capacitance of the capacitor bank in µF that is required. (b) Simulate the circuit in Matlab and verify your result.
1. A single phase circuit has a load of 500kVa at a power factor of 0.707...
1. A single phase circuit has a load of 500kVa at a power factor of 0.707 lagging. Calculate the kVA of the capacitors needed to improve the power factor to unity 3. When connected to a 120-v(rms), 60Hz power line, a load absorbes 4 kw at a lagging power factor of 0.8. Find the capacitance necessary to raise the pf to 0.9 4. A three phase motor draws 20kva at 0.707 power factor lagging from a 208V source. Determine the...
Two industrial loads each require 250∠0 V (rms) at 60Hz. Load 1 absorbs 8kW at 0.8...
Two industrial loads each require 250∠0 V (rms) at 60Hz. Load 1 absorbs 8kW at 0.8 leading; load 2 absorbs 20kVa at 0.6 lagging l. The line that transmits the power from the source to the load has an impedance of (0.05 + j0.5) Ohm a. Sketch the circuit b. find complex power for the line and the load c. Power (complex) supply by the source (proof the sums of all power equal to zero)
A 525 V to 110 V, 50 Hz, single phase transformer has a no-load current on...
A 525 V to 110 V, 50 Hz, single phase transformer has a no-load current on the HV side, of 0,5 A at a power factor of 0.36 lagging. Answer the following questions regarding this transformer: 3.1 If a load current of 24 A flows on the LV side, at a power factor of 0.8 lagging, find the value of the primary current and the power factor.   State the assumption and sketch the phasor diagram representing this situation.    (10) 3.2...
A three-phase 12-mile, 50 kV (line), 60 Hz line has a resistance of 0.1, capacitance of...
A three-phase 12-mile, 50 kV (line), 60 Hz line has a resistance of 0.1, capacitance of 0.01 and inductance of 1 mH/km. The load at the receiving end of the line absorbs 10 MVA at 90 percent of rated voltage. Calculate: ABCD parameters of the line The sending-end voltage if the load power factor is 0.8 lagging. The sending-end line voltage, line current and complex power if the load has a power factor of 0.7 leading.
A 400-k VA, 2300 230, 60-hz transformer supplies a 0.8 lagging power-factor load whose KVA Is...
A 400-k VA, 2300 230, 60-hz transformer supplies a 0.8 lagging power-factor load whose KVA Is adjustable from no load to 120 percent rated KVA. The percent resistance, percent reactance, and percent core loss are 56, 3.16, and 0.42 respectively. For 2 KVA increments of load, tabulate and plot the efficiency of the transformer from no load to 120 percent rated load. Please state the formulas clearly
A 10kW load with 0.65 pf lagging is supplied by an AC source rated 400V. A.)...
A 10kW load with 0.65 pf lagging is supplied by an AC source rated 400V. A.) draw the power triangle of the load B.)If a capacitor is connected across the load to correct its power fctor to 0.95 lagging, what will be the required size of the capacitor bank in kVAR? C.) Draw the new power triangle of the system. D.) what will be the new system current
A three-phase industrial load consists of 136 kW at 0.8 power factor lagging. What size capacitor...
A three-phase industrial load consists of 136 kW at 0.8 power factor lagging. What size capacitor bank is required to correct the power factor to 0.95 lagging
Electrical Circuit A) A factory (with frequency 60 HZ) has the following electrical loads: Induction motors   ...
Electrical Circuit A) A factory (with frequency 60 HZ) has the following electrical loads: Induction motors    of 16 kW at a lagging power factor of 0.8. Induction motors    of 20 kW at a lagging power factor of 0.7. Load of 12 KVA at a lagging factor of 0.9. Load of 10 KVAR at a leading factor of 0.8 a-what is the overall power factor of the factory. b- Assume that the voltage at the input to the factory is 440...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT