Question

Design a buck converter that steps down a 12V to a 5V. load such that the...

Design a buck converter that steps down a 12V to a 5V.

  • load such that the power consumption of the load is 0.2 mW
  • Load current ripple must be under 5%
  • Load voltage ripple must be under 5%
  • Assume no forward voltage on switch and diode

Assume any information, you need.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design a Boost Converter with the following characteristics: Vg = 100V, V = 200V, load power...
Design a Boost Converter with the following characteristics: Vg = 100V, V = 200V, load power 800W, switching frequency 100 kHz. For the design consider all elements to be ideal. 1) What is the duty cycle, D? 2) What is the inductor average current, IL? 3) Design the inductor and capacitor so that the peak-to-peak inductor current ripple is 40% of IL and the capacitor peak-to-peak voltage ripple is 2.5 % of V. 4) Draw the waveforms of voltage and...
Consider an ideal down converter supplying load resistance of 80 Ω from a voltage source rated...
Consider an ideal down converter supplying load resistance of 80 Ω from a voltage source rated 9 V and 250 mA. The converter operates at 70-kHz and is designed for 5% voltage ripple and 10% current ripple with a duty time of 60%. A) Calculate the output voltage, the output voltage ripple, output current and output current ripple. B) Calculate the cycle period, ton and toff C) Calculate the required inductance and capacitance values D) Calculate the output voltage as...
A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty...
A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty ratio d= 30%, load resistance R_L= 20Ω, inductance =100 μH, and capacitance= 680 μF. 1) Calculate the following values, and include units in your answers: a) Average output voltage,V_o b) Average output current,I_o c) Average input current,I_in d) Average current through the inductor in steady-state e) Peak-to-peak current ripple through the inductor, Δ_iL f) Average inductor current that will cause the converter to enter...
Problem 2: A photovoltaic module is used to supply constant 12 V that needed by a...
Problem 2: A photovoltaic module is used to supply constant 12 V that needed by a Tablet. Depending on insolation from the Sun, the photovoltaic module’s output voltage is changing between 18 V to 36 V (dc). Thus, a buck converter is used between the netbook and the photovoltaic module. 1) What is the duty ratio range of the dc/dc converter? 2) If the inductance of the buck converter inductor is 40 uH, what is the minimum switching frequency to...
Full wave rectifier is used to design a DC power supply. The DC power supply has...
Full wave rectifier is used to design a DC power supply. The DC power supply has an average output voltage of 12v on which the maximum ripple allowed is 1v (peak to peak). The rectifier feeds a load of 200ohm . The rectifier is supplied from 170v at 60 hz ac line through a transformer. Assume Vy= 0.7v . a) Find the transformer tarns ratio? b) Find the required value of the capacitor? c) Specify the PIV rating of the...
Design a DC power supply that will deliver 100mA of current to a load with a...
Design a DC power supply that will deliver 100mA of current to a load with a ripple of 5%. Use a full wave rectifier and a 17 Peak Voltage Source with F= 60 Hz. Load resistance = 1k So Basically you just need to find the capacitance of the filtering capacitor. Please tell me how. This is what I did, but I think I'm wrong. The Vripple I got is (.05)*17 = .85 V. Then according to my manual, C...
A) You are in a situation where you need to control a load that draws 1A...
A) You are in a situation where you need to control a load that draws 1A from an approximately 12V supply. The control signal that you have available is a 0-1V signal capable of sourcing 100mA. Choose a type of transistor to implement this control and show a circuit diagram for how you might hook it up. B) For this problem, the load and its power supply are the same as in the previous problem, but the control comes from...
Question 1: please choose the correct answer only without explain anything: ___________ or inductors may distort...
Question 1: please choose the correct answer only without explain anything: ___________ or inductors may distort the rectifier output because of the charging and discharging of those devices Capacitors Resistors Semiconductors insulators An LED emit light when __________ biased. Open Reverse Forward Shunt The voltage output from a bridge rectifier looks like a continuous series of half-wave pulses from the AC source with peaks that slightly lower because of the barrier voltage of __________ diodes Two Four Eight Six A...
PLEASE DRAW THE CIRCUIT DIAGRAMS OF EACH DEFINITIONS AND GIVE ITS APPLICATIONS. PLEASE GIVE THE FULL...
PLEASE DRAW THE CIRCUIT DIAGRAMS OF EACH DEFINITIONS AND GIVE ITS APPLICATIONS. PLEASE GIVE THE FULL DETAILS OF THE STEPS ON EACH QUESTIONS SO I COULD FOLLOW UP YOUR WHOLE EXPLANATIONS. PLEASE WRITE THE STEPS ON SOLVING THIS EXAMPLE EX) STEP 1, STEP 2, ETC HANDWRITING IS OKAY AS LONG AS IT IS READABLE. IF YOU HAVE USED THE EQUATIONS OR CONCEPTS, PLEASE STATE IT CLEARLY WHICH ONE YOU HAVE YOU USED SO I COULD FULLY UNDERSTAND THE DETAILS OF...
QUESTION 1 The term "Slip" indicates the difference between the motor's synchronous speed and the no-load...
QUESTION 1 The term "Slip" indicates the difference between the motor's synchronous speed and the no-load speed True False 1 points    QUESTION 2 Wet Bulb (WB) Temperature: is for the temperature reading form an ordinary mercury bulb thermometer or regular temperature sensor. True False 1 points    QUESTION 3 The refrigerant (R-134a) is the new replacement of the refrigerant (R-22) as it is less harmful to the environment. True False 1 points    QUESTION 4 Draft Gauge and Bourdon...