Question

A Chebyshev filter must have an attenuation of at least 20dB at twice the cut-off frequency...

A Chebyshev filter must have an attenuation of at least 20dB at twice the cut-off frequency of 3kHz. The filter has 1dB ripple in the passband. Find the transfer function of appropriate low-pass filter.

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
10.4 - The first order analog low pass filter H(s) = 1500/(s + 1500) must be...
10.4 - The first order analog low pass filter H(s) = 1500/(s + 1500) must be transformed into a digital filter operating with an 8 kHz sampling rate. a. Prewarp the cut-off frequency for the filter and modify the analog transfer function accordingly. b. Find the transfer function for the digital filter. c. Find the difference equation for the filter. d. Find the frequency response and draw the filter shape. e. Find the digital filter shape directly from the magnitude...
Draw a 2nd order low pass filter with a flat passband gain of 5 to remove...
Draw a 2nd order low pass filter with a flat passband gain of 5 to remove the harmonic content of a 60 HZ square wave of triangular wave input. Design for a cut off frequency of 80 Hz. Use 50 K Ohm for the input resistance. Verify your answers using AC Sweep in PSPICE
Design a bandpass filter with a lower cut off frequency fLO= 1 KHz and bandwidth B=...
Design a bandpass filter with a lower cut off frequency fLO= 1 KHz and bandwidth B= 3 KHz. Given L=10 mH. Determine the center frequency ?0 and the quality factor Q of this filter.
Design a passive RC high pass filter with a cutoff frequency of 470 Hz using a...
Design a passive RC high pass filter with a cutoff frequency of 470 Hz using a 270 pF capacitor. What is the value of the resistor? Express your answer with the appropriate units. What is the transfer function of the filter? Express your answer in terms of the variables R, C, and s. If the filter is loaded with a resistor whose value is the same as the resistor in part B, what is the transfer function of this loaded...
Please show steps. Thank you Design an identical cascade unit gain active RC low pass filter...
Please show steps. Thank you Design an identical cascade unit gain active RC low pass filter of order 4. The cut frequency for the filter is 800Hz. Use 1.0uF capacitors. a) Draw the circuit and calculate the values of R. b) Express the transfer function of the filter H(s). c) Plot the Bode diagram of the frequency response of the filter. d) Estimate the output voltage if the filter is excited with an input voltage vi(t) = sin(15000t) e) What...
Second order circuit as a band pass filter. 1. Consider a series RLC circuit of your...
Second order circuit as a band pass filter. 1. Consider a series RLC circuit of your choice with AC source. Find the resonance conditions (resonant frequency, quality factor cut-off frequencies and bandwidth. Simulate(multisim) the resonance condition by experimenting with AC signal of several different frequencies and comparing the output amplitudes. You need to show graphs of simulation with several different frequencies. Demonstrate that the simulation results confirm the calculated resonance effect. Make a band pass filter from circuit in (1)....
A common use of capacitors as a reactive component is in a low-pass or high-pass filter,...
A common use of capacitors as a reactive component is in a low-pass or high-pass filter, both of which contain a resistor and a capacitor. A low-pass filter is one that passes through signals with frequencies lower than a particular cutoff frequency and causes attenuation in signals of higher frequency. A high-pass filter is one that passes through signals with frequencies higher than a certain cutoff and causes lower frequencies to attenuate, giving the two configurations their names. The cutoff...
A linear time invariant system has an impulse response given by ℎ[?] = 2(−0.5) ? ?[?]...
A linear time invariant system has an impulse response given by ℎ[?] = 2(−0.5) ? ?[?] − 3(0.5) 2? ?[?] where u[n] is the unit step function. a) Find the z-domain transfer function ?(?). b) Draw pole-zero plot of the system and indicate the region of convergence. c) Is the system stable? Explain. d) Is the system causal? Explain. e) Find the unit step response ?[?] of the system, that is, the response to the unit step input. f) Provide...
Classify each of the following as either true or false. (a) In the FIR design using...
Classify each of the following as either true or false. (a) In the FIR design using the window method, side lobes appear due to numerical round- off                                                                                                                                errors (b) The DC gain of the transfer function H(z) =   is 0.4 FIR Filters have all zeros at the origin. IIR (recursive) Filters can never be unstable Windows are used in FIR Filter design to reduce the size of side lobes in the frequency response. A causal Filter will always have a...
Question 1: Using a low pass filter, you would have seen a rhythmic fluctuation of the...
Question 1: Using a low pass filter, you would have seen a rhythmic fluctuation of the baseline at 50 cycles/ second due to: Select one: Interference from the electrical supply The low frequency vibration of the building Noise picked up from the fluorescent lights The low frequency vibration of the air conditioning The noise from the chatter of other students Question 2: The neuron's membrane potential has the ability to integrate its inputs over time. This can be done via,...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT