Question

Using MultisimBlue – Advanced Circuit Simulation Design Program make a I. CE Swamped Amplifier Circuit producing...

Using MultisimBlue – Advanced Circuit Simulation Design Program make a

I. CE Swamped Amplifier Circuit producing the following:

1. DC Current Gain: ?DC = 150 (minimum value) 2. AC Voltage Gain: Av = 12 (minimum value)

II. Required Components:

1. Transistor Q1 – 2N2222A producing a VCE between 8 V to 12 V

2. Input AC Source: 10 mVAC (14.14 mVpk) @ 1 kHz

3. Coupling and Bypass Capacitors – 30 µF (suitable for low frequencies)

4. Circuit VCC of 20 Volts 5. Source Resistance (RS) of 200 ?

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must...
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must provide features such as; mid-band gain of 100 with undistorted output, stable bias with voltage divider bias (from a 12 or 15V dc source), AC gain stability with emitter bypass capacitor, and coupling capacitors at the input and output to block the dc components. Your design should include complete calculations for choosing voltages, various circuit components (resistors, coupling capacitors), and the circuit diagram. The...
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must...
Design and implement a common-emitter audio amplifier using a general purpose transistor 2N3904. The design must provide features such as; mid-band gain of 100 with undistorted output, stable bias with voltage divider bias (from a 12 or 15V dc source), AC gain stability with emitter bypass capacitor, and coupling capacitors at the input and output to block the dc components. Your design should include complete calculations for choosing voltages, various circuit components (resistors, coupling capacitors), and the circuit diagram. The...
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS)...
-------Electronics 2------- 1. Design an amplifier using a MOSFET transistor (2N7000) with a Common Source (CS) configuration with a resistor in the Source. Its design should provide an amplification of -12V / V. 2. The voltage Vcc will be +8 vDC, the AC voltage will be 10 mV peak 5 kHz and the load resistance will be RL 2.2 kn. 3. Simulate the circuit in LTSpice. It must choose resistors Ro, Rs, RG1 and RG2 such that the circuit operates...
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband...
Design, simulate, and implement a multistage discrete amplifier using small-signal BJT transistors. Amplifier Specifications: – Midband voltage gain: Av = 100. – Lower 3-dB frequency: fc = 100 Hz. – Input Impedance: Zin ≥ 250 kΩ. – Output Impedance: Zo ≤ 100 Ω. – Power Supply: Vcc = 15 V. – The load resistance is 1 kΩ – Output capability with a 1–kHz sinusoidal test signal must be at least 2 V peak without severe distortion (i.e. clipping). – Transistor...
Design the circuit of a source follower JFET amplifier biasing circuit with load RL and input...
Design the circuit of a source follower JFET amplifier biasing circuit with load RL and input voltage internal resistance RS that having a gain of +0.2. The specification of the circuit is given as below: Supply voltage, VCC = +12 V; Input impedance, Zi = 10 k; cut-off frequency from source capacitor, fLS = 40 Hz; cut-off frequency from gate capacitor, fLG = 4 Hz; VGSQ = -2.86 V; IDSS = 16 mA and Vp = -4 V
1. If a system has a gain greater than 1: ____________________ 2. If a system has...
1. If a system has a gain greater than 1: ____________________ 2. If a system has a gain equal to 1: ____________________ 3. If a system has a gain less than 1: ____________________ 4. If a system has a gain greater than 0 dB: __________________ 5. If a system has a gain equal to 0 dB: ____________________ 6. If a system has a gain less than 0 dB: __________________ 7. For a voltage amplifier to increase the source voltage: Rin...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT