Question

Why is the voltage at the inverting terminal not exactly the same as that at the...

Why is the voltage at the inverting terminal not exactly the same as that at the noniverting (vi) For Op Amp
Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
1. For an inverting amplifier with a voltage gain of -10 and an input resistance of...
1. For an inverting amplifier with a voltage gain of -10 and an input resistance of 1 kilohm, calculate the value of the feedback resistor (Rf) in kilohms. 2. For a non-inverting amplifier with a voltage gain of 11, what is the ratio of R2 to R1? 3. Which pin of the 741 op-amp should be connected to the positive supply voltage (e.g. +15V)? 4. For an inverting amplifier with a voltage gain of -20 and an input resistance of...
1. Design an inverting amplifier with gain of ×10, and input impedance of 100Ω. 2. Design...
1. Design an inverting amplifier with gain of ×10, and input impedance of 100Ω. 2. Design a non-inverting amplifier with a gain of ×10. Design the amplifier so that the output current from the op-amp at maximum output voltage +15V is no larger than 15 mA. 3. Design a current summing amplifier that finds the algebraic sum of two input voltages: VOUT = - (V1 + V2) . Design the amplifier so that output current from the op-amp at maximum...
design (and draw ) an inverting amplifier by using op pamp with a voltage gain equals...
design (and draw ) an inverting amplifier by using op pamp with a voltage gain equals to -10 (Acl=Vout/Vin)
Consider an op-amp connected in an inverting configuration to realize a closed-loop gain of -100 V/V...
Consider an op-amp connected in an inverting configuration to realize a closed-loop gain of -100 V/V utilizing resistors of 1k and 100 k. A load resistance RLis connected from the output to ground, and a low-frequency sine-wave signal of peak amplitude Vpeakis applied to the input. Let the op amp be ideal except that its output voltage saturates at 10 Vand its output current is limited to the range of 20 mA. 1) For RL = 1k, what is the...
6.    Answer the following questions: a.    What is the difference between Op-Amp circuit and Comparator circuit? b.    Discuss some...
6.    Answer the following questions: a.    What is the difference between Op-Amp circuit and Comparator circuit? b.    Discuss some of the issues with this Op-Amp oscillations and explain the voltage swing and cause of potential failure of this circuit. c.     What makes the comparator circuit oscillate and more ideal for the applications? d.    Describe the operation of the comparator oscillator circuit and explain the difference in inverting and non-inverting waveforms of the comparator e.    What is the significance of using comparator circuit to achieve sinusoidal oscillations?
Why does the terminal at higher voltage indicate the current is flowing out of the solenoid...
Why does the terminal at higher voltage indicate the current is flowing out of the solenoid and the lower voltage indicate the current is flowing into the solenoid?
If you connect a resistor to a battery with a given emf, the measured terminal voltage...
If you connect a resistor to a battery with a given emf, the measured terminal voltage is V. Next you connect in parallel another resistor to the first one. As a result, The terminal voltage increases; The terminal voltage decreases; The terminal voltage depends only on the internal resistance of the battery and doesn’t depend on a load.
Design an op-amp circuit for a weighted summer that shifts the dc level of the input...
Design an op-amp circuit for a weighted summer that shifts the dc level of the input signal vi(t) = 3 sin(t) V from zero to -3 V. Assume that in addition to vi(t), you have a dc voltage source of 1.5 V available. Sketch the output signal waveform.
Deisgn an op-amp circuit that will give you an output voltage from 5V to 0V. There...
Deisgn an op-amp circuit that will give you an output voltage from 5V to 0V. There must be a resistor where when the resistance is 3475 voltage is 5v and when the resitance is 10,000 the output votlage must be zero.
Design an Op-Amp phase shift circuit that must accept a sine waveform voltage at its input...
Design an Op-Amp phase shift circuit that must accept a sine waveform voltage at its input ??? (?) = 10 sin (120??) mV, and must provide at its output, an output voltage of 1.2 Vrms and with an offset of −120 ° with respect to the input signal.
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT