Question

What is 'opamp open-loop cutoff frequency'? is it a default value of op-amp or should i...

What is 'opamp open-loop cutoff frequency'? is it a default value of op-amp or should i calculate it case by case?

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Estimate the magnitude of the loop gain of the circuit .The op-amp has the following parameters:...
Estimate the magnitude of the loop gain of the circuit .The op-amp has the following parameters: differential input resistance, rd = 1 M?, output resistance, ro = 100 ?, open-loop gain, Aol = 105. Assume R1 = 24.01 k? and R2 = 5.89 k?
1. Calculate the input difference in potential (eNI − eINV) for an op amp amplifier with...
1. Calculate the input difference in potential (eNI − eINV) for an op amp amplifier with an output voltage of 10 V and an open loop gain of a. 2000 b. 30,000 2. Locate specifications for the LM741 and the LF411 (National Semiconductor). For each determine the worst case a. input impedance. b. open loop gain c. gain bandwidth. 3. Assuming β = 0.05, and AOL = 2000, calculate the closed loop gain using the approximation.
Consider an op-amp connected in an inverting configuration to realize a closed-loop gain of -100 V/V...
Consider an op-amp connected in an inverting configuration to realize a closed-loop gain of -100 V/V utilizing resistors of 1k and 100 k. A load resistance RLis connected from the output to ground, and a low-frequency sine-wave signal of peak amplitude Vpeakis applied to the input. Let the op amp be ideal except that its output voltage saturates at 10 Vand its output current is limited to the range of 20 mA. 1) For RL = 1k, what is the...
How would I simulate an Ideal Differential op amp in a NETLIST in LTSPICE IV? What...
How would I simulate an Ideal Differential op amp in a NETLIST in LTSPICE IV? What is the NETLIST line of code?
Answer the following waveguide fundamental questions A)What is the value of the cutoff frequency for a...
Answer the following waveguide fundamental questions A)What is the value of the cutoff frequency for a TE32 mode in an air filled waveguide of dimensions 4 centimetres by 3 centimetres? B) If a wave is introduced at a lower frequency than the cutoff frequency, what happens? C) If a wave is introduced at a higher frequency than the cutoff frequency, what happens? D) What is the value of the cutoff frequency and the useful operating frequency range for a waveguide...
Operational amplifiers have an intrinsic gain (sometimes called the open loop gain), which refers to the...
Operational amplifiers have an intrinsic gain (sometimes called the open loop gain), which refers to the "multiplier" in the amplification of the inputs to produce the output. Which of the following statements is generally true for operational amplifiers, and indicates the approximation for an ideal op-amp? a. Intrinsic gain is a very large number, and in the ideal case approaches an infinite value. b. Intrinsic gain is a very small number, and in the ideal case approaches zero. c. Intrinsic...
Design an active-RC low pass second order Butterworth filter for a cutoff frequency of 1 kHz,...
Design an active-RC low pass second order Butterworth filter for a cutoff frequency of 1 kHz, and a pass band gain of 2 V/V. Use a 741 Op Amp. If using Table I, use a capacitor value of 0.1 μF for C and C1, otherwise you may use any capacitors available in the lab. If applicable, make an excel worksheet showing the calculations required for the above design.  Choose appropriate real resistor values for the designed circuit and simulate this circuit...
An active low pass filter (with op-amp), the capacitor value is 500 pf, the resistor value...
An active low pass filter (with op-amp), the capacitor value is 500 pf, the resistor value is 1kΩ and the input signal source is 20 V. a)draw the complete circuit with the data provided in the example b) plot the frequency response graph of the filter, use at least 5 dots for the plot of the graph and identify in it the pass band and the attenuation band. c) determine the filter output voltage f = 100KHz and f =...
Should you be able to see a bacteriophage on an inoculation loop? For class, I am...
Should you be able to see a bacteriophage on an inoculation loop? For class, I am working on isolating a bacteriophage and I feel at times confused on what I should be expecting. I labeled the clear zones that are suspected bacteriophage and when I rested my inoculation loop on top of the area, I see nothing and feel nothing (I don't know what I expected, but it just makes me apprehensive that I'm not doing this right?) I, then,...
You should now explore and document the following: 1. How can I watch a variable changing?...
You should now explore and document the following: 1. How can I watch a variable changing? 2. How can I watch the special function registers (SFR)? What does the program counter do when I step through my program? How does this relate to the program memory? 3. How does my C-code translate into assembly code? Can I simulate assembly commands? 4. Set the simulator to 16MHz (Project Properties -> Simulator) and use the Stopwatch to measure how long it takes...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT