Question

Draw the output load voltage, load current waveforms along with ac source voltage of a fully...

Draw the output load voltage, load current waveforms along with ac source voltage of a fully
controlled bridge rectifier connected with inductive load with firing angle α = 30°. Assume the
load current is continuous.

Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

sorry if you cannnot understand my writing and please adjust with my writing for the next time i will improve gradually

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Q3/ Draw the out voltage and current waveforms of a single-phase cycloconverter connected to a purely...
Q3/ Draw the out voltage and current waveforms of a single-phase cycloconverter connected to a purely resistive load. The following information could be useful: Load Supply Voltage, Supply Frequency Output Frequency Firing Angle At 20Ω 230Vrms , 50 Hz 12.5 1/300 sec Your drawing should contain all the details including Amplitudes, Time, Degrees and Axis Names.
An AC voltage source is connected to a 22.0 Ω resistor. The output voltage of the...
An AC voltage source is connected to a 22.0 Ω resistor. The output voltage of the source is given by the function Δv = (100 V)sin[(50π rad/s)t]. (a) From the equation for the output voltage, what is the maximum voltage across the resistor (in V)? V (b) From the equation for the output voltage, what is the frequency of oscillation of the current through the resistor (in Hz)? Hz (c) What is the rms voltage across the resistor (in V)?...
An AC voltage source has an RMS voltage of 10 volts and it is connected in...
An AC voltage source has an RMS voltage of 10 volts and it is connected in series to an inductor, a capacitor, and a resistor. At the resonant frequency the maximum current in the circuit is 7 amps and the inductive reactance is 10 Ohms. What is the maximum current in the circuit, in amps, at a frequency which is a factor of 2.5 more than the resonant frequency? ***PLEASE ONLY ANSWER IF 100% CORRECT***
An AC voltage source has an output of ∆V = 177.0 sin(459t) Volts. Calculate the RMS...
An AC voltage source has an output of ∆V = 177.0 sin(459t) Volts. Calculate the RMS voltage. What is the frequency of the source? Calculate the voltage at time t = 1/117 s. Calculate the maximum current in the circuit when the generator is connected to an R = 60.0 Ω resistor.
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with...
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with a peak-to-peak riple of 2V to a load. The average load current is 100 mA. Assume that ideal diodes and 60-Hz ac volatage sources of any amplitudes needed are avaialable. Draw the circuit diagram for your design, Specify the values of all components used. 2. Repeat Problem 1 with 2 diodes and out-of-phase voltage sources to form a full-wave rectifier.
A 10kW load with 0.65 pf lagging is supplied by an AC source rated 400V. A.)...
A 10kW load with 0.65 pf lagging is supplied by an AC source rated 400V. A.) draw the power triangle of the load B.)If a capacitor is connected across the load to correct its power fctor to 0.95 lagging, what will be the required size of the capacitor bank in kVAR? C.) Draw the new power triangle of the system. D.) what will be the new system current
An AC source of rms voltage 50 V and frequency 150 Hz is connected to the...
An AC source of rms voltage 50 V and frequency 150 Hz is connected to the primary coil of a transformer that has 5000 turns on the primary side and 7500 turns on the secondary side. If the secondary coil is connected to a 150 ohm load, determine the current flowing through the primary coil. 0.75 A 1.25 A 0.25 A 0.50 A
The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230...
The controlled full wave rectifier is connected to the grid. The rms grid voltage is 230 Volt at 50 Hz. 24 Volt battery will be charged with 15A. An inductor, which is series connected to the battery, is used to limit the current ripple. Only The second harmonics of the output voltage is taken into account. The inductor R/L ratio is 50. The current ripple is allowed to be 4 amp peak to peak. Determine the firing angle and R...
Develop an expression for current in a controlled half-wave rectifier circuit that has a load consisting...
Develop an expression for current in a controlled half-wave rectifier circuit that has a load consisting of a series Resitor R and dc voltage VDC. The source is vs=Vm sin wt, and the delay angle is alpha. (a) Determine the average current if Vm=100 V,R=100 ohms, Vdc=24 V,w= 2p60 rad/s, and alpha= 75°.
A 210 V, 1200 rpm, 10 A separately excited motor is controlled by 1- phase fully...
A 210 V, 1200 rpm, 10 A separately excited motor is controlled by 1- phase fully controlled converter with an ac source voltage of 230 V, 50 Hz. Assume that sufficient inductance is present in the armature circuit to make to motor current continuous and ripple free for any torque greater than 25% of rated torque, and Ra = 1.5 Ω. i. What should be the value of the firing angle for the rated torque at motoring +ve (1200rpm) ii....
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT