Question

What happens in the DC motor when it is suppose started from its rated armature voltage?...

What happens in the DC motor when it is suppose started from its rated armature voltage?
What will be the typical firing angle at start for DC motor fed from ac-to-dc controlled
rectifier?

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A separate excited DC motor is running at 1000 rpm when the armature voltage is 600...
A separate excited DC motor is running at 1000 rpm when the armature voltage is 600 V. The motor has a field constant Kphi = 4 V.sec and the armature resistance of the motor is 0.8 Ohms. i. Calculate the value of the resistance of the dynamic braking at full load. The armature current should be limited to 200 % of the rated value. ii. If the motor operates in regenerative braking at a speed of 1200 rpm, calculate the...
A 220 V, 960 rpm, 20 A separately excited DC motor has armature resistance and inductance...
A 220 V, 960 rpm, 20 A separately excited DC motor has armature resistance and inductance of 1.2 ohms and 50 mH respectively. Motor is controlled by a single phase half controlled rectifier with source voltage of 230 V, 50Hz. (a) Calculate no load speeds and speeds and developed torques on the boundary between continuous and discontinuous conduction for ą = 45°, 90° and 135°. (b) Calculate and plot speed torque curve for ą = 45°.
A 152 V DC shunt motor has an armature resistance of 0.3ohm, a brush voltage drop...
A 152 V DC shunt motor has an armature resistance of 0.3ohm, a brush voltage drop of 2 V, the rated full load current is 70 A. A) calculate the current at the instant of starting as a percentage of full load current B) calculate the value of starting resistance of limit the motor current at the instant of starting to 150 percent of the rated load current
A dc motor has an armature resistance of 1 ?, and K? = 3 Vsec. When...
A dc motor has an armature resistance of 1 ?, and K? = 3 Vsec. When the motor’s terminal voltage is adjusted to 320 V, the motor speed is 1000 r/min. A TVR braking is applied, a) Calculate the value of the braking resistance that would reduce the maximum braking current to twice the rated current. b) Calculate the new motor steady state speed if the load is bidirectional and braking resistance is taken off.
A 25-hp, 240V, DC shunt motor has armature and field resistances of 0.2 ? and 120...
A 25-hp, 240V, DC shunt motor has armature and field resistances of 0.2 ? and 120 ?, respectively. At no load and rated voltage, the motor draws a line current of 5A and its speed is 1250 rpm. When driving a certain load, the input to the motor is 15KW. For this condition, find: a.The speed of the motor b.The developed torque The efficiency of the motor at this load
Design of DC Motor Starter In order for a dc motor to function properly, it must...
Design of DC Motor Starter In order for a dc motor to function properly, it must be protected from physical damage during the starting period. At starting conditions, the motor is not rotating, and armature generated voltage EA = 0 V. Since the internal resistance of a normal DC motor is very low, a very high current flows. It is possible for a motor to be severely damaged by such currents, even if they last for only a moment. A...
Design of DC Motor Starter In order for a dc motor to function properly, it must...
Design of DC Motor Starter In order for a dc motor to function properly, it must be protected from physical damage during the starting period. At starting conditions, the motor is not rotating, and armature generated voltage EA = 0 V. Since the internal resistance of a normal DC motor is very low, a very high current flows. It is possible for a motor to be severely damaged by such currents, even if they last for only a moment. A...
A 210 V, 1200 rpm, 10 A separately excited motor is controlled by 1- phase fully...
A 210 V, 1200 rpm, 10 A separately excited motor is controlled by 1- phase fully controlled converter with an ac source voltage of 230 V, 50 Hz. Assume that sufficient inductance is present in the armature circuit to make to motor current continuous and ripple free for any torque greater than 25% of rated torque, and Ra = 1.5 Ω. i. What should be the value of the firing angle for the rated torque at motoring +ve (1200rpm) ii....
In order for a dc motor to function properly, it must be protected from physical damage...
In order for a dc motor to function properly, it must be protected from physical damage during the starting period. At starting conditions, the motor is not rotating, and armature generated voltage EA = 0 V. Since the internal resistance of a normal DC motor is very low, a very high current flows. It is possible for a motor to be severely damaged by such currents, even if they last for only a moment. A solution to the problem of...
A 5-kW, 220-V shunt motor has an armature resistance of 0.15 ? and a field-circuit resistance...
A 5-kW, 220-V shunt motor has an armature resistance of 0.15 ? and a field-circuit resistance of 100 ?. The motor delivers rated output power at rated voltage when its armature current is 20 A. When the motor is operating at rated voltage, the speed is observed to be 1000 r/min when the machine is loaded such that the armature current is 15 A. In order to protect both the motor and the dc supply under starting conditions, an external...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT