Question

1) A DC machine induces an EMF of 240 v at 1500 rpm. Find the developed...

1) A DC machine induces an EMF of 240 v at 1500 rpm. Find the developed torque for an armature current of 25A.

2) Draw and explain all characteristics of d.c. Shunt motor.

3) State accessitivity of 3 point starter.

4) A four pole wave connected dc armature has 50 slots with 10 conductors per slot. The armature is rotated at 1000 rpm of the useful flux per pole is 30mwb, calculate the amount of EMF induced.

5) A 6 pole lap wound shunt motor has 600 conductors in the armature. The resistance of the armature and field winding is 0.2 ohm and 55 ohms respectively. The flux per pole is 25mwb. Find the speed of the motor, when it takes 100 A from dc motor of 220 V supply.

6) Draw and explain all characteristics of dc series motor.

7) Explain the significance of back emf.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
B// A 4- pole 220 V, lap wound shunt D.C motor runs at 800 rpm takes...
B// A 4- pole 220 V, lap wound shunt D.C motor runs at 800 rpm takes 35 A. The shunt field resistance is 110 Ω and armature resistance is 0.4 Ω iron and friction losses is 800 W. Find. a- Maximum efficiency. b- The resistance sections of starter connected to this motor by using same armature resistance and voltage supply from above. if maximum armature current is 50 A and the resistance of first section is 1.95 Ω
Q3: (a) Determine the terminal voltage of a dc shunt generator which develops an e.m.f. of...
Q3: (a) Determine the terminal voltage of a dc shunt generator which develops an e.m.f. of 240V and has an armature current of 50 A on load. Assume the armature resistance is 0.04Ω. [3 marks] (b) A lap wound armature is used in a 4-pole dc machine and 70 coils on the armature each containing 10 turns. The flux per pole in the machine is 40 mWb and the machine rotates at 500 rpm; (a) How many current paths are...
A 60 kW, 400 V d.c. shunt motor has 4 poles a 2-circuit wave-connected armature winding...
A 60 kW, 400 V d.c. shunt motor has 4 poles a 2-circuit wave-connected armature winding with 450 conductors. The flux per pole is 45 mWb. The full-load efficiency of the motor is 90.5%. The armature and interpole windings have a total resistance of 0.1 Ω. The shunt field resistance is 200 Ω. Calculate (i) the line current (ii) full-load speed and (iii) armature torque.
The no-load (line) voltage of a 6-pole, 72-slot, 1200-rpm, three-phase, Y-connected, synchronous generator is 1732 V....
The no-load (line) voltage of a 6-pole, 72-slot, 1200-rpm, three-phase, Y-connected, synchronous generator is 1732 V. There are 10 conductors per slot. For a series connection, determine (a) the frequency of the induced emf and (b) the flux per pole.
A dc shunt generator runs at 500 rpm at 200 V. It is delivering 50,000 W...
A dc shunt generator runs at 500 rpm at 200 V. It is delivering 50,000 W . The armature resistance is 0.02 Ω and the field resistance is 40 Ω. Calculate the emf generated. Assume brush drop of 1V per brush. Show all steps and circuit diagram if needed.
The full-load armature current of a 5 hp, 150 V shunt dc motor is 30 A....
The full-load armature current of a 5 hp, 150 V shunt dc motor is 30 A. The field (shunt) resistance and the armature resistance of the motor are ????F = 125 ? and ???????? = 0.15, respectively. At a random speed of 1800 rpm magnetization curve of the motor has measured and is shown in the table below. ????0 (V) armature voltage 10 90 110 140 170 185 ???????? (A) field (shunt) current 0 0.82 1 1.2 1.7 2.88 Calculate...
a)Explain the shunt excitation and compound excitation of DC generator. b)A 240V compound DC motor has...
a)Explain the shunt excitation and compound excitation of DC generator. b)A 240V compound DC motor has the armature, series field and shunt field resistances are 0.22 Ω, 0.04 Ω and 200 Ω respectively. On full load, the line current is 17.5 A and the motor runs at 1800 rpm. (short shunt) i) Draw the diagram and the power flow of the motor. ii) Find the back EMF of the motor. iii) Find the mechanical power developed. iv) Find the output...
A 200 V DC, 1,800 RPM shunt connected motor has an armature resistance of 0.4 ohm...
A 200 V DC, 1,800 RPM shunt connected motor has an armature resistance of 0.4 ohm and a brush resistance of 0.4 ohm; brush voltage drop of 6.0 V, independent of load. The resistance of the shunt field is 230 ohm. The full load rated line current is 40 A. When the motor is operated at no load the line current is 5 A and the speed is 1750 RPM. Calculate speed at rated load Calculate speed at .3 rated...
Question 2 The full-load armature current of a 5 hp, 150 V shunt dc motor is...
Question 2 The full-load armature current of a 5 hp, 150 V shunt dc motor is 30 A. The field (shunt) resistance and the armature resistance of the motor are ????F=125 ? and ????????=0.15, respectively. At a random speed of 1800 rpm magnetization curve of the motor has measured and is shown in the table below. EO(V) armature voltage 10 90 110 140 170 185 IF (A) field (shunt) current 0 0.82 1 1.2 1.7 2.88 Calculate the following: a....
Q.1: Choose the correct answer (and expalin) for the follwoings: Minimum number of coils for 400...
Q.1: Choose the correct answer (and expalin) for the follwoings: Minimum number of coils for 400 V, 6-pole lap connected de machine for a maximum voltage of 15 V between adjacent commutator segments should be (a) 80 (b) 160 (c) 200 (d) 400 The armature resistance of a 6-pole lapp wound de machine is 0.05 Q. If the aramture is re-wound using a wave winding, then the armature resistance will be (a) 0.452 (b) 0.30 (c) 0.15 (d) 0.102 A...