Question

Determine the amplitude modulation ratio and frequency modulation ratio of a unipolar PWM switching Inverter. The...

Determine the amplitude modulation ratio and frequency modulation ratio of a unipolar
PWM switching Inverter. The triangle waveform has peak-to-peak voltage of 2 volts at a
frequency of 25 kHz and the control waveform is v(t) = 0.85 sin 377t.

Homework Answers

Answer #1

Frequency modulation ratio is the ratio of frequency of carrier signal to the frequency of reference signal( sinusoidal).

Amplitude modulation ratio is the ratio of amplitudes of reference sinusoidal signal to the carrier triangular signal.

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Draw the circuit for a three-phase full-bridge non-isolated inverter. Describe how the converter works using switching...
Draw the circuit for a three-phase full-bridge non-isolated inverter. Describe how the converter works using switching waveforms. Include a description of two different control strategies using PWM and square-wave phase difference methods. Clearly define the amplitude and frequency modulation indexes in the PWM method. Discuss and calculate the rms phase and line voltages when the DC input voltage is 400V.
A buck converter has an input voltage V in = 24 V, switching frequency f s...
A buck converter has an input voltage V in = 24 V, switching frequency f s = 100 kHz, duty ratio d = 50%, load resistance R L = 10 Ω , inductance 100 μH, and capacitance 680 μF. 1) Calculate the following values, and include units in your answers : a) Average output voltage, V_o b) Average output current, I_o c) Peak - to - peak current ripple, Δi_L d) Output current that will cause the converter to enter...
A boost converter has an input voltage Vin= 10 V, switching frequency fs= 100 kHz, duty...
A boost converter has an input voltage Vin= 10 V, switching frequency fs= 100 kHz, duty ratio d=50%, load resistance RL= 20 Ω, inductance 100 μH, and capacitance 680 μF. Qualitatively describe the effect on Io, Δi_L, and Δv_C if you: a) Increase the duty ratio b) Increase the switching frequency c) Increase the load resistance
If the instantaneous value of a voltage in an AC circuit of the communication system (at...
If the instantaneous value of a voltage in an AC circuit of the communication system (at any time t seconds) is given by V= 142sin(8πt-0.125π) volts, determine: a. The amplitude, b. Periodic time (in ms) c. Frequency d. Phase angle in degrees e. Voltage at t=0 f. Voltage at t=10ms g.Time when voltage reaches 100volts h. Time when voltage is maximum i. Sketch one cycle of the waveform j. Given that the voltage waveform can also be represented as V=Rsin(ωt+θ),...
A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty...
A buck-boost converter has an input voltage V_in= 10 V, switching frequency fs= 100 kHz, duty ratio d= 30%, load resistance R_L= 20Ω, inductance =100 μH, and capacitance= 680 μF. 1) Calculate the following values, and include units in your answers: a) Average output voltage,V_o b) Average output current,I_o c) Average input current,I_in d) Average current through the inductor in steady-state e) Peak-to-peak current ripple through the inductor, Δ_iL f) Average inductor current that will cause the converter to enter...
1. An ac generator has a frequency of 2.5 kHz and a voltage of 240 V....
1. An ac generator has a frequency of 2.5 kHz and a voltage of 240 V. An inductance L1 = 6.0 mH is connected across its terminals. Then a second inductance L2 = 8.0 mH is connected in parallel with L1. Find (a) the current that the generator delivers to L1 2. A 8.3-mH inductor is connected to an ac generator (11 V rms, 750 Hz). Determine the peak value of the current supplied by the generator. Note: The ac...
Please solve the questions for the following problems. a. In an overdamped natural response, S1=200 rad/sec,...
Please solve the questions for the following problems. a. In an overdamped natural response, S1=200 rad/sec, S2=3000rad/sec, v(0)=20v, and dv(0)/dt = 10v/sec. Determine the voltage equation v(t) . b. For a given series RLC circuit, R=632?, L=100mH, and C=1.001uF. Determine what kind of damping is the circuit. c. How do you determine if a circuit is overdamped? There may be multiple answers so give a specific answer as it applies to RLC circuits. d. Is a critically damped circuit practical...