Question

In a circuit of frequency radius, a resistance of 200? serves as a load at the...

In a circuit of frequency radius, a resistance of 200? serves as a load at the end of a 50 ? transmission line. We wish to connect a capacitor, C, in parallel with the entrance line so that a source with 50 ? exit impedance doesn't see reflections

a) Determine the minimum length of the transmission line in terms of wave length.

b) Determine the reactance value of the capacitor.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
In a radio frequency circuit, a 100Ω resistor serves as a load at the end of...
In a radio frequency circuit, a 100Ω resistor serves as a load at the end of a 50Ω transmission line. We wish to connect a capacitor, C, in parallel to the input of the line so that a source with output impedance of 50 Ω do not see reflections. a. Determine the minimum length of the transmission line in terms of long wave. b. Determine the value of the capacitor reactance.
in a circuit of radio frequency, a resistance of 165 ohms serves as load to the...
in a circuit of radio frequency, a resistance of 165 ohms serves as load to the final of a transmission line of 75 ohms. We wish to use a parallel open stub to achieve maximum power transfer. Use the smith chart to get values. a) Determine the minimum distance in wavelengths from the load that has to be connected to the stub. b) Determine the minimum length of the stub in wave lengths.
A generator with rms voltage of rms = 120 V drives an RLC circuit at frequency...
A generator with rms voltage of rms = 120 V drives an RLC circuit at frequency f = 60 Hz. The load resistance R and reactance values of the inductor L and the capacitor C of the circuit are given by R = 50 , XL = 50 , XC = 150 , respectively What is the impedance of the circuit? What is the peak current amplitude in the circuit? What is the phase angle  of the circuit? The...
Design the circuit of a source follower JFET amplifier biasing circuit with load RL and input...
Design the circuit of a source follower JFET amplifier biasing circuit with load RL and input voltage internal resistance RS that having a gain of +0.2. The specification of the circuit is given as below: Supply voltage, VCC = +12 V; Input impedance, Zi = 10 k; cut-off frequency from source capacitor, fLS = 40 Hz; cut-off frequency from gate capacitor, fLG = 4 Hz; VGSQ = -2.86 V; IDSS = 16 mA and Vp = -4 V
In the RC circuit, as frequency increases, the value of the resistance and the capacitance remained...
In the RC circuit, as frequency increases, the value of the resistance and the capacitance remained constant and the output gain began to decay exponentially. From a theoretical point of view the impedance of a capacitor is (-j)/wc. By applying the mathematical representation of voltage gain [H(w0)= v0/vi] , we end up with the following formula: 1/(1+jwRC), where V0 is 1/jwC, and Vi is the summation of the total input impedance as seen by the voltage source which is R...
Electrical Circuit A) A factory (with frequency 60 HZ) has the following electrical loads: Induction motors   ...
Electrical Circuit A) A factory (with frequency 60 HZ) has the following electrical loads: Induction motors    of 16 kW at a lagging power factor of 0.8. Induction motors    of 20 kW at a lagging power factor of 0.7. Load of 12 KVA at a lagging factor of 0.9. Load of 10 KVAR at a leading factor of 0.8 a-what is the overall power factor of the factory. b- Assume that the voltage at the input to the factory is 440...
1) 2 point charges are separated by a distance of 8 cm. The left charge is...
1) 2 point charges are separated by a distance of 8 cm. The left charge is 48 mC and the right charge is -16mC. Using a full sheet of paper: draw the 2 charges separated by 8cm, centered in the sheet. (if you are missing a ruler estimate 8cm as ⅓ a paper sheet length). [6] a) Draw field lines to indicate the electric fields for this distribution. [4] b) Draw 3 equipotential surfaces, 1 each, that pass: -Through the...
Please provide a brief overview on: chapter 21 1. Can I obtain the net electric field...
Please provide a brief overview on: chapter 21 1. Can I obtain the net electric field due to two or more point charges? 2. Can I obtain the net Coulomb force on a point charge due to two or more point charges? 3. Can I draw physical quantities (for example, velocity, forces or electric fields) involved in a given problem in a diagram? 4. Do I have a good "qualitative" understanding of the motion of a charged particle in a...
Please read the article and answear about questions. Determining the Value of the Business After you...
Please read the article and answear about questions. Determining the Value of the Business After you have completed a thorough and exacting investigation, you need to analyze all the infor- mation you have gathered. This is the time to consult with your business, financial, and legal advis- ers to arrive at an estimate of the value of the business. Outside advisers are impartial and are more likely to see the bad things about the business than are you. You should...