Question

A six-phase star rectifier has a purely resistive load of R = 10ohms. The peak supply...

A six-phase star rectifier has a purely resistive load of R = 10ohms. The peak supply voltage Vm = 170 V, and the supply frequency f = 60 Hz. Determine the average output voltage of the rectifier if the source inductance is negligeble

Homework Answers

Answer #1

given Vm=170

Vdc=(3*170/3.14)

162.42V

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
A full-wave rectifier has a 120 V rms, 60 Hz ac source. The load is a...
A full-wave rectifier has a 120 V rms, 60 Hz ac source. The load is a series inductance, resistance and dc voltage source, with L = 100 mH, R = 10 Ω, and Vdc = 50 V. a). Determine an expression for load current. b). Determine the power absorbed by the dc voltage source. c). Determine the power absorbed by the resistance. d). Determine the power factor of the source.
A three-phase six-step inverter delivers power to a resistive load from a 450 V dc source....
A three-phase six-step inverter delivers power to a resistive load from a 450 V dc source. For a star-connected load of 10 ? per phase, determine: (i) rms value of load current (ii) rms value of IGBT current (iii) Load power.
Develop an expression for current in a controlled half-wave rectifier circuit that has a load consisting...
Develop an expression for current in a controlled half-wave rectifier circuit that has a load consisting of a series Resitor R and dc voltage VDC. The source is vs=Vm sin wt, and the delay angle is alpha. (a) Determine the average current if Vm=100 V,R=100 ohms, Vdc=24 V,w= 2p60 rad/s, and alpha= 75°.
Q3/ Draw the out voltage and current waveforms of a single-phase cycloconverter connected to a purely...
Q3/ Draw the out voltage and current waveforms of a single-phase cycloconverter connected to a purely resistive load. The following information could be useful: Load Supply Voltage, Supply Frequency Output Frequency Firing Angle At 20Ω 230Vrms , 50 Hz 12.5 1/300 sec Your drawing should contain all the details including Amplitudes, Time, Degrees and Axis Names.
Full wave rectifier is used to design a DC power supply. The DC power supply has...
Full wave rectifier is used to design a DC power supply. The DC power supply has an average output voltage of 12v on which the maximum ripple allowed is 1v (peak to peak). The rectifier feeds a load of 200ohm . The rectifier is supplied from 170v at 60 hz ac line through a transformer. Assume Vy= 0.7v . a) Find the transformer tarns ratio? b) Find the required value of the capacitor? c) Specify the PIV rating of the...
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with...
1. Design a full-wave bridge rectifier power supply to deliver an average voltage of 9V with a peak-to-peak riple of 2V to a load. The average load current is 100 mA. Assume that ideal diodes and 60-Hz ac volatage sources of any amplitudes needed are avaialable. Draw the circuit diagram for your design, Specify the values of all components used. 2. Repeat Problem 1 with 2 diodes and out-of-phase voltage sources to form a full-wave rectifier.
A single-phase full-bridge inverter has RLC load of R = 4 ? and L = 35...
A single-phase full-bridge inverter has RLC load of R = 4 ? and L = 35 mH and C = 155 ?F. The dc input voltage is 230 V and the output frequency is 50 Hz. (a) Find an expression for load current up to fifth harmonic. (b)Calculate rms value of fundamental load current (c) The power absorbed by load and the fundamental power (d)The rms and peak current of each IGBT (e) Conduction time of IGBTs and diodes if...
A single phase half wave converter in is operated from a 120 V 60 Hz supply...
A single phase half wave converter in is operated from a 120 V 60 Hz supply and a freewheeling diode is connected across the load. the load consists of series connected resistance R= 10 ohm inductance L= 5mH and battery E=20V. Express the instantaneous output voltage in fourirer series and determine the rms value of the lowest order output harmonic current.
The ac voltage controller is used for heating a resistive load of R= 5 ohms and...
The ac voltage controller is used for heating a resistive load of R= 5 ohms and input voltage is V=120V (rms), 60Hz. The thristor switch is on for n=125cycles and is off for m=75 cycles. Determine the rms output voltage, the input power factor and the average as well as rms currents of the thyristor
A three phase balanced resistive load has a line voltage VL = 381.05 V and line...
A three phase balanced resistive load has a line voltage VL = 381.05 V and line current IL = 30 A. Calculate 1) the total power taken by the load 2) the power taken by each phase of the load.