Question

1.a) A counter is designed to go through the sequence : 1,3,5,7,0,2,5,6, repeat, Using JK flipflops:...

1.a) A counter is designed to go through the sequence : 1,3,5,7,0,2,5,6, repeat, Using JK flipflops: (i) Construct the state table. (ii) Draw the circuit. b) A sequential circuit is constructed with one T flip-flop A, one D flip-flop B and one input X, when X=0, the state of the circuit remains the same. When X=1, the circuit goes through the transitions from 00 to 01 to 11 to 10 back to 00, repeat. (i) Draw the state transition diagram (ii) Construct the state Table (iii) Draw the circuit.

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Use JK Flip Flop to design a 2-bit synchronous counter (up counter) that counts down as...
Use JK Flip Flop to design a 2-bit synchronous counter (up counter) that counts down as given: AB = 01, 11, 00, 10, and then again 01. Show the design steps (e.g state table, j and k inputs for k-maps etc) and draw the final circuit.
A Sequential Circuit has two D Flip-Flops, C and H, and one input x. When x...
A Sequential Circuit has two D Flip-Flops, C and H, and one input x. When x = 0, the state of the circuit remains the same. When x =1, the circuit goes through the state transitions from 00 to 01 to 11 to 10 back to 00, and repeats. Design the sequential circuit.
Sequence is 000,0110,111,100,101,001, (repeat)000,…
Sequence is 000,0110,111,100,101,001, (repeat)000,…· Design a counter that counts in the sequence assigned to you. Use D flip-flops, NAND gates, and inverters. Draw your circuit explicitly showing all connections to gate and flip-flop inputs.Explicitly means that you should draw in all wires, don’t just label the inputs and outputs. Show switches connected to thePreset and Clear inputs of the flip-flops. Use one switch for all clears and a separate switch for each preset.· Explain in detail how you can set...
1) Design a sequential circuit with two D flip-flops, A and B, and one input, x....
1) Design a sequential circuit with two D flip-flops, A and B, and one input, x. When x = 0, the circuit state does not change. When x = 1, the circuit stops through the state transitions from 00 to 01, from 01 to 10, from 10 to 11, finally back to 00 and the sequence repeats. to. Find the state diagram b. Find the table of states c. Find the equations of state d. Find the logic diagram
Design a sequential circuit with two J-K flip-flops P and M and two inputs E and...
Design a sequential circuit with two J-K flip-flops P and M and two inputs E and X. If E = 1, the circuit remains in the same state, regardless of the value of X. When E = 0 and X = 1, the circuit goes through the state transitions from 00 to 01 to 10 to 11, back to 00, and then repeats. When E = 0 and X = 0, the circuit goes through the state transitions from 00...
Design a 2-bit binary counter using one JK and one T flip flop. Derive the equations...
Design a 2-bit binary counter using one JK and one T flip flop. Derive the equations for JA, KA and TB. Do not draw the circuit.
You have a bit counter that follows the sequence (ABC) 000, 110, 111, 100, 101, 001,...
You have a bit counter that follows the sequence (ABC) 000, 110, 111, 100, 101, 001, (repeat back to 000) You have and input x. If x = 1 the sequence moves in the -> direction If x = 0 the sequence moves in the <- direction a) draw the FSM graph (5pts) b) create the next state table (5 pts) c) create the next state map (5pts) d) create the implementation for the flip flop inputs. A is D-ff,...
Design a counter which counts in the sequence that has been assigned to you. Use D...
Design a counter which counts in the sequence that has been assigned to you. Use D flip flops and NAND gates. Simulate your design using SimUaid. Submit the state table, D flip-flop input equations, and transition graph determined in Part 6. The D flip-flop equations can be derived using Karnaugh maps or using LogicAid by entering a state table with zero input variables. Sequence: 000,100,001,110,101,111,(repeat) 000,... Also, please answer the following questions: How can a D flip-flop be set to...
It is desired to produce a synchronous counter using JK flip-flops and performing a sequence determined...
It is desired to produce a synchronous counter using JK flip-flops and performing a sequence determined according to a C command. If C = 0, {0, 6, 2, 1, 4, 0 ...} If C = 1, {0, 6, 5, 7, 2, 1, 0 ...} Give the equations associated with each JK flip-flop to perform the requested cycle, for each case (C = 0 and C = 1) separately. please design each separately, this question was already answered but not spereratley,...
Design a sequencer using J-K flip-flops that will sequence through the following states and then repeat...
Design a sequencer using J-K flip-flops that will sequence through the following states and then repeat the sequence in response to successive clock pulses:      0,1,3,5,7,4,0,………….. PLEASE INCLUDE ALL OF THE FOLLOWING: -a state diagram -a binary state transition table -K-maps and reduced expressions for all J-K inputs -logic diagram
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT