Question

On Logisim , Design a circuit that creates an alarm with a delay of 10 seconds...

On Logisim , Design a circuit that creates an alarm with a delay of 10 seconds to start. The alarm will be on for 10 seconds. You can use a push button to simulate a switch.


Thank you!


Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
The software I am using Is Logisim. Design and build a circuit to add 2 2-bit...
The software I am using Is Logisim. Design and build a circuit to add 2 2-bit binary numbers. This means that you will have 4 input lines and 3 output lines. The three output lines are 2 bits for the sum and a carry out line. Use logisim to construct your circuit. Upload the .circ file to blackboard
Circuit Design problem : to take Alexa alarm as an audio output To Trigger a light...
Circuit Design problem : to take Alexa alarm as an audio output To Trigger a light switch to turn on A fluorescent lightbulb from the standard home power supply. When I wake up to Alexa alarm I want the basement light to turn on. What simple circuit could I build to make this happen?
Design a circuit for a synchronous 4-bit counter. Your counter should count up starting from 0...
Design a circuit for a synchronous 4-bit counter. Your counter should count up starting from 0 to 9 (00002 to 10012) and then wind back to 0 (00002) – after 9, it should go back to 0. Use 4 JK flip-flops and any other gates you need. Include your design documentation in your submission: a. Truth table b. Simplification (show your work) 2. Build this circuit in Logisim. Please label each gate, including flip-flops. You may need the following wiring...
design a C++ program that make use to embedded in a Arduino micro controller. that will...
design a C++ program that make use to embedded in a Arduino micro controller. that will control a conveyor belt. the program must be able to start and stop the conveyor belt. should have 3 led light on it.( red led is used when conveyor is running) (yellow led is when conveyor is about to move must blink 10 times and should sound a beeping alarm) (green is when conveyor is stop) you also have to add a Start and...
Q2 Design a PLC program, for the conveyor belts that bring out the suitcases at an...
Q2 Design a PLC program, for the conveyor belts that bring out the suitcases at an airport. The circuit must operate as follows: • When the START (a Normally Open push button) is pressed, a siren will sound for 30 seconds. • After 30 seconds, the conveyor will operate, and the siren will stop sounding. • If the STOP (a Normally Closed push button) is pushed, the conveyor will stop. • If the STOP is pressed during the period that...
Design a door code detector (Mealy machine) that has two inputs S and Y where S...
Design a door code detector (Mealy machine) that has two inputs S and Y where S is the start signal (by a push button) and Y gives the code that is a sequence of logic 0’s and 1’s (by a switch). The detector has one output Z (LED). To open the door (i.e., Z=1), you have to press the S button once and after that, input Y with sequence 100*10 where 0* means zero or more (i.e., any number of)...
Design a sequential circuit that will negate four-bit two's complement integer. That is if, for example,if...
Design a sequential circuit that will negate four-bit two's complement integer. That is if, for example,if the input is 3 (in two's compliment representation) the output should be -3 (in two's complement notation). Start with the truth table, next write the formulas for each output in SOP form, next simplify formulas using Karnaugh maps and finally draw the simplified circuit. Thank you
Design an RLC series circuit with the following data: Z0 = 100 Ω (Characteristic impedance) Frequency...
Design an RLC series circuit with the following data: Z0 = 100 Ω (Characteristic impedance) Frequency = 1 kHz (Frequency where reactance is zero) R = Z0. a. Sketch the impedance on a log-log scale. What do you expect the phase to do? b. Simulate the circuit in QUCS and compare the result with your prediction/expectation. Also elaborate on your interpretation of the response. c. Can you identify Zo and Frequency features? How well does your design meet the requirements?...
Design a 4-bit adder-subtractor circuit using the 4-bit binary Full adders (74LS83) and any necessary additional...
Design a 4-bit adder-subtractor circuit using the 4-bit binary Full adders (74LS83) and any necessary additional logic gates. The circuit has a mode input bit, M, that controls its operation. Specifically, when M=0, the circuit becomes a 4-bit adder, and when M=1, the circuit becomes a 4-bit subtractor that performs the operation A plus the 2’s complement of B.Where A and B are two 4-bits binary numbers. That is, * When M=0, we perform A+B, and we assume that both...
1. Create a voltage divider. Design a circuit which can provide a fraction of the voltage...
1. Create a voltage divider. Design a circuit which can provide a fraction of the voltage ( x V) out of the regular batteries. The equipment you can use: 2 D-batteries (about 1.5V each) and one piece of nichrome wire and some connecting wires. If you need to make 2V, how would you connect it? Draw a detailed circuit to show the connection. Explain in detail why it works. Use a voltmeter to check your design. Draw the voltmeter on...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT