Question

From a decade counter with an input clock signal of 6MHZ what its the frequency at...

From a decade counter with an input clock signal of 6MHZ what its the frequency at Q3

1- 600 kHz

2-1.5 MHZ

3- 289 kHz

The answer its 600 KHZ ...but why ? PLease explain as detailed as you can

Homework Answers

Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
4-bit register using jk flip flops. 1)What is the purpose of anding the clock signal and...
4-bit register using jk flip flops. 1)What is the purpose of anding the clock signal and the load input together in your circuit? 2) How would I be able to store 1011 into the 4-bit register? Explain the process. For example, what do your inputs should be? Should your clock be on or off? How about your load input? How does your load input work when you want to store bits into your register? 3) If your load input is...
A 1 kHz sine wave is sampled at frequency of 5 kHz (d) What if the...
A 1 kHz sine wave is sampled at frequency of 5 kHz (d) What if the original analog signal included both even and odd harmonics of its primary frequency; that is, 2, 3, 5 kHz, etc. What would be the highest harmonic that will be faithfully represented in the discrete-time version of the analog signal? (e) Following on with the previous step, what is the lowest harmonic that will be aliased and what would be resulting alias frequency?
QUESTION 1 How many possible states can be represented by a 5-bit state register? QUESTION 2...
QUESTION 1 How many possible states can be represented by a 5-bit state register? QUESTION 2 When a clock signal changes from 1 to 0, this is referred to as the... Period Falling edge Rising edge Frequency QUESTION 3 What is the minimum number of bits required in order for a state register to represent an FSM with 24 states? 0.5 points    QUESTION 4 What is the clock period for a clock with a frequency of 16 MHz? Note:...
What would happen with the ring counter if the reset switch set the value of the...
What would happen with the ring counter if the reset switch set the value of the counter to a ‘3’ instead of a ‘1’? Group of answer choices There would be a false output, but the counter would continue to run in the proper order after the “3” state The counter will count in the sequence: 3 -> 6 -> 5 -> 3 -> 6 -> ... which means two “on” outputs will be shifted left. The “3” state was...
Hi, Given: R = 30 ohm/km L = 20mh/km C = 50 nF/km G = 20nS/km...
Hi, Given: R = 30 ohm/km L = 20mh/km C = 50 nF/km G = 20nS/km f = 10 kHz, 10 MHz, 1.5 MHz 1) Calculate the Zo of the transmission line (in a table) 2) Calculate the speed of propagation of the signal 3) What can be said about the nature of wave propagation on this line? Thank you.
QUESTION 1 During a single clock tick, how many 64-bit values can be written to an...
QUESTION 1 During a single clock tick, how many 64-bit values can be written to an input of a register file with 8 64-bit registers (i.e. an 8x64 register file)? QUESTION 2 Suppose you are designing a processor that contains a register file with 32 32-bit registers (i.e. a 32x32 register file). What is the minimum number of bits required in order to select which register is being written to? QUESTION 3 If the decimal value, 30, is shifted to...
Design a counter which counts in the sequence that has been assigned to you. Use D...
Design a counter which counts in the sequence that has been assigned to you. Use D flip flops and NAND gates. Simulate your design using SimUaid. Submit the state table, D flip-flop input equations, and transition graph determined in Part 6. The D flip-flop equations can be derived using Karnaugh maps or using LogicAid by entering a state table with zero input variables. Sequence: 000,100,001,110,101,111,(repeat) 000,... Also, please answer the following questions: How can a D flip-flop be set to...
Question 3: Diagnose a novel set of signal transduction pathways (8 pts) You isolate cells from...
Question 3: Diagnose a novel set of signal transduction pathways (8 pts) You isolate cells from the brain of a mouse, and work to characterize them. In your first experiments you grow your cells in a petri dish, and add various signals to the petri dish and determine how the cells respond. You get the following information. Assume there are no other genes or signals beyond what is mentioned. Hint: sometimes it helps to sketch the signal pathways first, and...
Problem 3: Nyquist Theorem (10 pts) With 32 levels of signal and a bandwidth f=1 MHz,...
Problem 3: Nyquist Theorem (10 pts) With 32 levels of signal and a bandwidth f=1 MHz, what is the maximum data rate by the Nyquist theorem? Please include your calculation steps. Answers without intermediate work will not receive any point. (Hint: Nyquist theorem in Ch02 slides# 56) Your solution: Data rate = 2 * 1mhz * log2(32) = 2* 1 Mhz * 5 =10 bps Can someone check my work if i did this correctly? thank you
What would happen to a protein like signal peptidase if you removed its signal peptide but...
What would happen to a protein like signal peptidase if you removed its signal peptide but added a nuclear localization signal (NLS)? It would end up in the nucleus. It would end up in the cytoplasm It would be secreted None of the above What would happen to a secreted protein (e.g. insulin) if you produced it from an mRNA missing the sequence encoding the signal peptide? It would be properly secreted, though it might not fold correctly. It would...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT