Question

Sketch a 2nd order high pass circuit diagram, write the equation for the cut off frequency...

  1. Sketch a 2nd order high pass circuit diagram, write the equation for the cut off frequency calculation, and draw the frequency response curves with cut off frequency fc: assume that all resistors are 10kΩ and all capacitor are 10nF.
Engineering   Electrical-Engineering   
0 0
Add a commentTranscribed image text
Next >

Homework Answers

Answer #1

Problem

Solution

high pass circuit for a given specifications is drawn and calculations is done below

0 0
Know the answer?
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for?
Ask your own homework help question
Similar Questions
Design a second order (two pole) low-pass filter for the following specifications Cut-off frequency, fo or...
Design a second order (two pole) low-pass filter for the following specifications Cut-off frequency, fo or fH = 8kHz   Maximally Flat, i.e. Q=1/√2 > Justify any assumption you make. > Draw circuit with all designed values. > Draw the frequency response (Gain magnitude only)
Draw the circuit of second order low pass Butterworth filter and design it at a high...
Draw the circuit of second order low pass Butterworth filter and design it at a high cutoff frequency of 1KHz. Draw the frequency response of the designed filter.
Draw the circuit of second order low pass Butterworth filter and design it at a high...
Draw the circuit of second order low pass Butterworth filter and design it at a high cutoff frequency of 1KHz. Draw the frequency response of the designed filter.
7) (a) Draw a circuit of a high pass RL filter b) Derive the expression for...
7) (a) Draw a circuit of a high pass RL filter b) Derive the expression for V_o/V_i of a high pass RL filter (c) Use the equation you derived in (b) to determine the gain when (i) the frequency is very low (ii) R = X_L (iii) the frequency is very high (d) Use the equation you derived in (b) to determine the phase angle when (i) the frequency is very low (ii) R = X_L (iii) the frequency is...
What is the relationship between the poles of a high pass and low pass filter and...
What is the relationship between the poles of a high pass and low pass filter and the cut off frequency? How do I design a circuit that gives a specific cut off? for instance, an active high pass first order filter with a cut off frequency of 100khz?
Design a 2nd order high pass Butterworth for fo=3kHz. Determine the sensitivity of the frequency and...
Design a 2nd order high pass Butterworth for fo=3kHz. Determine the sensitivity of the frequency and Q parameters to component variations in your design.
Second order circuit as a band pass filter. 1. Consider a series RLC circuit of your...
Second order circuit as a band pass filter. 1. Consider a series RLC circuit of your choice with AC source. Find the resonance conditions (resonant frequency, quality factor cut-off frequencies and bandwidth. Simulate(multisim) the resonance condition by experimenting with AC signal of several different frequencies and comparing the output amplitudes. You need to show graphs of simulation with several different frequencies. Demonstrate that the simulation results confirm the calculated resonance effect. Make a band pass filter from circuit in (1)....
Draw a 2nd order low pass filter with a flat passband gain of 5 to remove...
Draw a 2nd order low pass filter with a flat passband gain of 5 to remove the harmonic content of a 60 HZ square wave of triangular wave input. Design for a cut off frequency of 80 Hz. Use 50 K Ohm for the input resistance. Verify your answers using AC Sweep in PSPICE
When determining the function of a circuit (high-pass, low-pass, band-pass and band-reject) how do we use...
When determining the function of a circuit (high-pass, low-pass, band-pass and band-reject) how do we use frequency at 0 and finite frequency to determine the circuits function only given the circuit? I'm given a circuit and want to determine whether it's a high-pass, low-pass, band-pass or band-reject - all passive filters. I know I have to determine whether there is an open, closed, or short circuit at the inductor or capacitor (or both) but don't know how to determine these....
SHOW STEPS CLEARLY PLEASE A client asks you to design an active high-pass filter. They specify...
SHOW STEPS CLEARLY PLEASE A client asks you to design an active high-pass filter. They specify a few needs: the gain should be 10, the corner frequency should be 2 kHz, and the gain roll-off rate should be 40 dB/decade. Unfortunately,you only have access to 4 resistors: 3 x 10-kΩ, and 1 x 100-kΩ. Design and draw a simple circuit that achieves the requested features keeping in mind the limited resistors available to you.Be sure to calculate all values of...
ADVERTISEMENT
Need Online Homework Help?

Get Answers For Free
Most questions answered within 1 hours.

Ask a Question
ADVERTISEMENT